Difference between revisions of "VTube-LASER Addata ZModem Communications Protocol"
From ATTWiki
(→Video of RECALL and SEND) |
|||
| (12 intermediate revisions by one user not shown) | |||
| Line 1: | Line 1: | ||
| − | [[image:Addata ZModem Icon Large.png | + | <table> |
| + | <tr cellpadding=10> | ||
| + | <td width=225> | ||
| + | [[image:vtube-laser_logo_1.96.png|300px]] | ||
| + | |||
| + | |||
| + | ==Addata ZModem Protocol== | ||
| + | |||
| + | * Back to [[VTube-LASER]] | ||
| + | * Back to [[VTube Software Updates]] (for LASER Mode) | ||
| + | * Download in updates the [https://www.advancedtubular.com/customers/vtube/ VTube-LASER Support Page] | ||
| + | |||
| + | |||
| + | </td> | ||
| + | <td width=300> | ||
| + | [[image:Addata ZModem Icon Large.png]] | ||
| + | </td> | ||
| + | </tr> | ||
| + | </table> | ||
| + | |||
| + | __TOC__ | ||
| + | |||
== About the Addata ZModem Communications Protocol== | == About the Addata ZModem Communications Protocol== | ||
| Line 6: | Line 27: | ||
<td width=300> | <td width=300> | ||
The Addata ZModem communications protocol is also known as the Addison "Non-Standard Device Interface".<br><br> | The Addata ZModem communications protocol is also known as the Addison "Non-Standard Device Interface".<br><br> | ||
| − | It allows for ZModem file transfer between VTube-LASER and any bender that complies with this | + | It allows for ZModem file transfer between VTube-LASER and any bender that complies with this protocol. (For example, the Arena software bender controls.)<br><br> |
<td> | <td> | ||
</td> | </td> | ||
| Line 18: | Line 39: | ||
<tr valign=top> | <tr valign=top> | ||
<td width=300> | <td width=300> | ||
| − | + | VTube-LASER allows you to setup the COM port configuration to match the configuration at the other end of the serial port connection. Enter System Options, click on the Measure 2 tab, then click on Benderlink. Set the protocol to Addata ZModem, and click on the COM port cell to display this COM port configuration dialog. | |
<td> | <td> | ||
</td> | </td> | ||
<td> | <td> | ||
[[image:vtube-laser_v2.8.3_AddataZModem_Benderlink_ComSetup.png|600px]] | [[image:vtube-laser_v2.8.3_AddataZModem_Benderlink_ComSetup.png|600px]] | ||
| + | </tr> | ||
| + | </table> | ||
| + | <br><br> | ||
| + | |||
| + | == VIDEO of RECALL and SEND == | ||
| + | <table cellpadding=10 width=900> | ||
| + | <tr valign=top> | ||
| + | <td width=300> | ||
| + | Click on the image on the right to see a RECALL/SEND with an Arena Control bender.<td> | ||
| + | </td> | ||
| + | <td> | ||
| + | [[image:vtube-laser_v2.8.3_AddataZModem Video.png|600px|link=https://www.advancedtubular.com/vtube-laser/vtube-laser_v2.8.3_addata_zmodem_protocol.mp4]] | ||
</tr> | </tr> | ||
</table> | </table> | ||
<br><br> | <br><br> | ||
Latest revision as of 16:01, 25 May 2017
|
Addata ZModem Protocol
|
|
Contents |
About the Addata ZModem Communications Protocol
|
The Addata ZModem communications protocol is also known as the Addison "Non-Standard Device Interface". |
|
|
VTube-LASER allows you to setup the COM port configuration to match the configuration at the other end of the serial port connection. Enter System Options, click on the Measure 2 tab, then click on Benderlink. Set the protocol to Addata ZModem, and click on the COM port cell to display this COM port configuration dialog. |
|
VIDEO of RECALL and SEND
| Click on the image on the right to see a RECALL/SEND with an Arena Control bender. |
|
