Difference between revisions of "VTube-LASER Addata ZModem Communications Protocol"

From ATTWiki
Jump to: navigation, search
(Created page with "== About the Addata ZModem Communications Protocol== <table cellpadding=10 width=900> <tr valign=top> <td width=300> The Addata ZModem communications protocol is also known a...")
 
(Video of RECALL and SEND)
 
(15 intermediate revisions by one user not shown)
Line 1: Line 1:
 +
<table>
 +
<tr cellpadding=10>
 +
<td width=225>
 +
[[image:vtube-laser_logo_1.96.png|300px]]
 +
 +
 +
==Addata ZModem Protocol==
 +
 +
* Back to [[VTube-LASER]]
 +
* Back to [[VTube Software Updates]] (for LASER Mode)
 +
* Download in updates the [https://www.advancedtubular.com/customers/vtube/ VTube-LASER Support Page]
 +
 +
 +
</td>
 +
<td width=300>
 +
[[image:Addata ZModem Icon Large.png]]
 +
</td>
 +
</tr>
 +
</table>
 +
 +
__TOC__
 +
 
== About the Addata ZModem Communications Protocol==
 
== About the Addata ZModem Communications Protocol==
  
Line 5: Line 27:
 
<td width=300>
 
<td width=300>
 
The Addata ZModem communications protocol is also known as the Addison "Non-Standard Device Interface".<br><br>
 
The Addata ZModem communications protocol is also known as the Addison "Non-Standard Device Interface".<br><br>
It allows for ZModem file transfer between VTube-LASER and any bender that complies with this Addata protocol.<br><br>
+
It allows for ZModem file transfer between VTube-LASER and any bender that complies with this protocol. (For example, the Arena software bender controls.)<br><br>
[[image:Addata ZModem Icon Large.png]]
+
 
<td>
 
<td>
 
</td>
 
</td>
Line 18: Line 39:
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
This protocol allows you to setup the COM port configuration to match the configuration at the other end of the serial port connection.  Set the protocol to Addata ZModem, then click on the COM port cell to display this COM port configuration dialog.
+
VTube-LASER allows you to setup the COM port configuration to match the configuration at the other end of the serial port connection.  Enter System Options, click on the Measure 2 tab, then click on Benderlink. Set the protocol to Addata ZModem, and click on the COM port cell to display this COM port configuration dialog.
 
<td>
 
<td>
 
</td>
 
</td>
 
<td>
 
<td>
 
[[image:vtube-laser_v2.8.3_AddataZModem_Benderlink_ComSetup.png|600px]]
 
[[image:vtube-laser_v2.8.3_AddataZModem_Benderlink_ComSetup.png|600px]]
 +
</tr>
 +
</table>
 +
<br><br>
 +
 +
== VIDEO of RECALL and SEND ==
 +
<table cellpadding=10 width=900>
 +
<tr valign=top>
 +
<td width=300>
 +
Click on the image on the right to see a RECALL/SEND with an Arena Control bender.<td>
 +
</td>
 +
<td>
 +
[[image:vtube-laser_v2.8.3_AddataZModem Video.png|600px|link=https://www.advancedtubular.com/vtube-laser/vtube-laser_v2.8.3_addata_zmodem_protocol.mp4]]
 
</tr>
 
</tr>
 
</table>
 
</table>
 
<br><br>
 
<br><br>

Latest revision as of 16:01, 25 May 2017

Vtube-laser logo 1.96.png


Addata ZModem Protocol


Addata ZModem Icon Large.png

Contents


About the Addata ZModem Communications Protocol

The Addata ZModem communications protocol is also known as the Addison "Non-Standard Device Interface".

It allows for ZModem file transfer between VTube-LASER and any bender that complies with this protocol. (For example, the Arena software bender controls.)

Vtube-laser v2.8.3 Addata ZModem Send.png

VTube-LASER allows you to setup the COM port configuration to match the configuration at the other end of the serial port connection. Enter System Options, click on the Measure 2 tab, then click on Benderlink. Set the protocol to Addata ZModem, and click on the COM port cell to display this COM port configuration dialog.

Vtube-laser v2.8.3 AddataZModem Benderlink ComSetup.png



VIDEO of RECALL and SEND

Click on the image on the right to see a RECALL/SEND with an Arena Control bender.

Vtube-laser v2.8.3 AddataZModem Video.png