Difference between revisions of "The Effect of Changing Cut Length with No Adjustment to the Draw Bender"

From ATTWiki
Jump to: navigation, search
(Created page with "<table> <tr cellpadding=10> <td width=225> 300px * Back to VTube-LASER * Back to VTube Software Updates (for LASER Mode) </td> ...")
 
(→‎What Happens When the Cut Length is Adjusted Without a Corresponding Adjustment to the Carriage Position)
 
(6 intermediate revisions by one user not shown)
Line 18: Line 18:
 
__TOC__
 
__TOC__
  
−
== The Effect ==
+
== What Happens When the Cut Length is Adjusted Without a Corresponding Adjustment to the Carriage Position==
  
−
<table cellpadding=10 width=900>
+
<table cellpadding=10 width=1000>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
−
In a situation where the part shape qualifies and the length on end A qualifies, but the length at end B is LONG, then it is usually still necessary to correct the bender after you change the Cut Length on the stick to use in bending.<td>
+
In a situation where the part shape qualifies and the length on end A qualifies, but the length at end B is LONG, then it is usually still necessary to send a correction to the bender after the user changes the Cut Length on the stick.<br><br>
 +
The reason is because reducing the cut length will pull the part back into the bender by the amount of the change when loading the part into the collet.<br><br>
 +
So, if cut length is changed to adjust and correct any part of the tube shape that is not end A, then the starting carriage location must also change.  In this case, it must move forward more than it did in the previous set up (when the cut length was longer).<td>
 
</td>
 
</td>
 
<td>
 
<td>
  
−
[[image:Cut Length Change No Bender Change.png|600px]]<br><br>
+
[[image:Cut Length Change No Bender Change.png|700px]]<br><br>
 
</tr>
 
</tr>
 
</table>
 
</table>
  
−
<table cellpadding=10 width=900>
 
−
<tr valign=top>
 
−
<td width=300>
 
−
VTube-LASER allows you to setup the COM port configuration to match the configuration at the other end of the serial port connection.  Enter System Options, click on the Measure 2 tab, then click on Benderlink. Set the protocol to Addata ZModem, and click on the COM port cell to display this COM port configuration dialog.
 
−
<td>
 
−
</td>
 
−
<td>
 
−
[[image:vtube-laser_v2.8.3_AddataZModem_Benderlink_ComSetup.png|600px]]
 
−
</tr>
 
−
</table>
 
−
<br><br>
 
−
 
−
== VIDEO of RECALL and SEND ==
 
−
<table cellpadding=10 width=900>
 
−
<tr valign=top>
 
−
<td width=300>
 
−
Click on the image on the right to see a RECALL/SEND with an Arena Control bender.<td>
 
−
</td>
 
−
<td>
 
−
[[image:vtube-laser_v2.8.3_AddataZModem Video.png|600px|link=https://www.advancedtubular.com/vtube-laser/vtube-laser_v2.8.3_addata_zmodem_protocol.mp4]]
 
−
</tr>
 
−
</table>
 
 
<br><br>
 
<br><br>

Latest revision as of 14:42, 2 May 2022

Vtube-laser logo 1.96.png



Contents


What Happens When the Cut Length is Adjusted Without a Corresponding Adjustment to the Carriage Position

In a situation where the part shape qualifies and the length on end A qualifies, but the length at end B is LONG, then it is usually still necessary to send a correction to the bender after the user changes the Cut Length on the stick.

The reason is because reducing the cut length will pull the part back into the bender by the amount of the change when loading the part into the collet.

So, if cut length is changed to adjust and correct any part of the tube shape that is not end A, then the starting carriage location must also change. In this case, it must move forward more than it did in the previous set up (when the cut length was longer).

Cut Length Change No Bender Change.png



Retrieved from "http://www.advancedtubular.wiki/index.php?title=The_Effect_of_Changing_Cut_Length_with_No_Adjustment_to_the_Draw_Bender&oldid=41927"