Difference between revisions of "Revision: Benderlink for BLM 3.2"
From ATTWiki
(→Other Pages) |
|||
| (5 intermediate revisions by one user not shown) | |||
| Line 6: | Line 6: | ||
<tr valign="top"> | <tr valign="top"> | ||
<td width = 200> | <td width = 200> | ||
| − | BLM benders can bend using [[draw bending]] or [[push-bending]]. BLM refers to push-bending as "[[variable radius bending]]." This version of Benderlink can recognize large radius push-bends and skip corrections to straights before and after push-bends. Also the bend angle of each push-bend is left untouched. | + | BLM benders can bend using [[rotary draw bending]] or [[push-roll bending]]. BLM refers to push-bending as "[[variable radius bending]]." This version of Benderlink can recognize large radius push-bends and skip corrections to straights before and after push-bends. Also the bend angle of each push-bend is left untouched. |
</td> | </td> | ||
</tr> | </tr> | ||
| Line 15: | Line 15: | ||
<tr valign="top"> | <tr valign="top"> | ||
<td width = 200> | <td width = 200> | ||
| − | Benderlink indicates which values are not corrected by showing a bold red value on the screen. The BLUE radius values indicates the Benderlink knows that | + | Benderlink indicates which values are not corrected by showing a bold red value on the screen. The BLUE radius values indicates the Benderlink knows that [[variable radius bending]] is in effect. |
</td> | </td> | ||
<td bgcolor="#e3e4f5"> | <td bgcolor="#e3e4f5"> | ||
| Line 48: | Line 48: | ||
Bender data was being output as integer data.</td> | Bender data was being output as integer data.</td> | ||
<td bgcolor="#e3e4f5"> | <td bgcolor="#e3e4f5"> | ||
| − | The | + | The precision is now set to four places beyond the decimal. |
</td> | </td> | ||
</tr> | </tr> | ||
| Line 55: | Line 55: | ||
<br><br> | <br><br> | ||
| − | + | ==Other Pages== | |
| − | + | ||
| − | + | *Go back to [[Benderlink]] | |
| + | *Go back to [[Benderlink for BLM]] | ||
| + | *Go to the [http://www.advancedtubular.com/blink_blm.htm main Benderlink for BLM page] | ||
| + | *About [[BLM]] Group USA | ||
Latest revision as of 04:08, 12 February 2009
New Recognition of Variable Radius Bending
|
BLM benders can bend using rotary draw bending or push-roll bending. BLM refers to push-bending as "variable radius bending." This version of Benderlink can recognize large radius push-bends and skip corrections to straights before and after push-bends. Also the bend angle of each push-bend is left untouched. |
|
Benderlink indicates which values are not corrected by showing a bold red value on the screen. The BLUE radius values indicates the Benderlink knows that variable radius bending is in effect. |
|
Set the Linear Units for Conversion
|
Benderlink now shows two radio-buttons in the Measuring Center section that allow the operator to send the data to the measuring center in a consistent unit value. |
|
Adjusted the BLM Data Output Accuracy
| Bender data was being output as integer data. |
The precision is now set to four places beyond the decimal. |
Other Pages
- Go back to Benderlink
- Go back to Benderlink for BLM
- Go to the main Benderlink for BLM page
- About BLM Group USA
