Difference between revisions of "Revision: Benderlink for BLM 3.2"

From ATTWiki
Jump to: navigation, search
(25px New Recognition of Variable Radius Bending)
(Other Pages)
 
(17 intermediate revisions by one user not shown)
Line 3: Line 3:
 
===[[image:Check.jpg|25px]] New Recognition of Variable Radius Bending ===
 
===[[image:Check.jpg|25px]] New Recognition of Variable Radius Bending ===
  
[[image:Benderlink_blm_variableradius1.jpg]|500px]
+
<table cellpadding="15" width = 500>
 +
<tr valign="top">
 +
<td width = 200>
 +
BLM benders can bend using [[rotary draw bending]] or [[push-roll bending]].  BLM refers to push-bending as "[[variable radius bending]]."  This version of Benderlink can recognize large radius push-bends and skip corrections to straights before and after push-bends.  Also the bend angle of each push-bend is left untouched.
 +
</td>
 +
</tr>
 +
</table>
 +
[[image:Benderlink_blm_variableradius1.jpg|500px]]
  
<table cellpadding="15" width = 650>
+
<table cellpadding="15" width = 500>
 
<tr valign="top">
 
<tr valign="top">
 
<td width = 200>
 
<td width = 200>
BLM benders can bend using [[draw bending]] or [[push-bending]]BLM refers to push-bending as "[[variable radius bending]]."  This version of Benderlink can recognize large radius push-bends and skip corrections to straights before and after push-bends.  Also the bend angle of each push-bend is left untouched.</td>
+
Benderlink indicates which values are not corrected by showing a bold red value on the screenThe BLUE radius values indicates the Benderlink knows that [[variable radius bending]] is in effect.
 +
</td>
 
<td bgcolor="#e3e4f5">
 
<td bgcolor="#e3e4f5">
[[image:Benderlink_blm_variableradius2.jpg]]
+
[[image:Benderlink_blm_variableradius2.jpg|300px]]
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 18: Line 26:
 
<br><br>
 
<br><br>
  
===[[image:Check.jpg|25px]] New Confirm File Overwrite ===
+
===[[image:Check.jpg|25px]] Set the Linear Units for Conversion===
  
 
<table cellpadding="15" width = 650>
 
<table cellpadding="15" width = 650>
 
<tr valign="top">
 
<tr valign="top">
 
<td width = 200>
 
<td width = 200>
Benderlink now requests operator confirmation when the operator is asking for a file overwrite during SAVE.
+
Benderlink now shows two radio-buttons in the Measuring Center section that allow the operator to send the data to the measuring center in a consistent unit value.
 
</td>
 
</td>
 
<td bgcolor="#e3e4f5">
 
<td bgcolor="#e3e4f5">
[[image:Benderlink_blm_confirmoverwrite.jpg]]
+
[[image:Benderlink_blm_unitsend.jpg]]
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 33: Line 41:
 
<br><br>
 
<br><br>
  
 
+
===[[image:Check.jpg|25px]] Adjusted the BLM Data Output Accuracy ===
 
+
===[[image:Check.jpg|25px]] New Convert SV Part Number to UPPER Case ===
+
  
 
<table cellpadding="15" width = 650>
 
<table cellpadding="15" width = 650>
 
<tr valign="top">
 
<tr valign="top">
 
<td width = 200>
 
<td width = 200>
Benderlink now automatically converts all SV part numbers to upper case when converting from BLM data.
+
Bender data was being output as integer data.</td>
</td>
+
 
<td bgcolor="#e3e4f5">
 
<td bgcolor="#e3e4f5">
[[image:Benderlink_blm_uppercase_svpartnumber.jpg|350px]]
+
The precision is now set to four places beyond the decimal.
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 50: Line 55:
 
<br><br>
 
<br><br>
  
===Other Pages===
+
==Other Pages==
Main [[Benderlink]] Wiki page<br>
+
 
Main [[Benderlink for BLM]] Wiki page<br><br>
+
*Go back to [[Benderlink]]
 +
*Go back to [[Benderlink for BLM]]
 +
*Go to the [http://www.advancedtubular.com/blink_blm.htm main Benderlink for BLM page]
 +
*About [[BLM]] Group USA

Latest revision as of 04:08, 12 February 2009

Benderlink blm logo.jpg

Check.jpg New Recognition of Variable Radius Bending

BLM benders can bend using rotary draw bending or push-roll bending. BLM refers to push-bending as "variable radius bending." This version of Benderlink can recognize large radius push-bends and skip corrections to straights before and after push-bends. Also the bend angle of each push-bend is left untouched.

Benderlink blm variableradius1.jpg

Benderlink indicates which values are not corrected by showing a bold red value on the screen. The BLUE radius values indicates the Benderlink knows that variable radius bending is in effect.

Benderlink blm variableradius2.jpg




Check.jpg Set the Linear Units for Conversion

Benderlink now shows two radio-buttons in the Measuring Center section that allow the operator to send the data to the measuring center in a consistent unit value.

Benderlink blm unitsend.jpg



Check.jpg Adjusted the BLM Data Output Accuracy

Bender data was being output as integer data.

The precision is now set to four places beyond the decimal.



Other Pages