Difference between revisions of "Modicon Momentum"

From ATTWiki
Jump to: navigation, search
(INPUT Base)
(Back of Modicon Momentum I/O Base)
Line 93: Line 93:
 
</table>
 
</table>
  
==Back of Modicon Momentum I/O Base==
 
  
<table>
 
 
<tr>
 
<td width="200">
 
This is the back of the base with a channel for receiving a DIN rail.</td>
 
<td>
 
[[image:tsxmomentum_back.jpg|300px]]
 
</td>
 
</tr>
 
 
</table>
 
  
 
==Modicon Momentum Analog Base==
 
==Modicon Momentum Analog Base==

Revision as of 21:35, 6 May 2010

Contents


Schneider Electronics Modicon Momentum Package

Schneider Electronics design allows manufacturers to control machinery using modules that specialize on a particular function - like motion control, I/O, digital to analog, weight measurement, etc. Each of the modules can be placed around cnc machinery in convenient locations, then connected to a central computer using cable or wireless connection that attaches to communications adaptors that snap onto each module. Several types of adaptors are available for different communications protocols.

We use the TCP/IP Ethernet style of communication adapter.

Schneider multiple communications adapters.jpg


I2T IFC220E Servo Base or Module

The I2T (Pronounced "I Square T") servo modules use the same package form as the other Modicon products. The base unit contains a computer that can control 2 axes.

This is the form for the I2T servo modules with an Ethernet Communications Adapter on the top. You can see a slight difference on the base from the INPUT module with the RJ-45 receptacle.

Momentum.jpg

In the I2T servo modules, the serial port is an RJ-45 receptacle port shown in this image. INPUT and OUTPUT modules don't include this port.

Momentum serial port.jpg


INPUT Base

INPUT Base

This is an INPUT base with 32-points with an Ethernet Communications Adapter clipped on the top.

See this data sheet (16 pages) for an overview of these modules.

View the Modicon Momentum I/O Base User Guide (662 pages).

They mount to DIN rails in electrical panels.

Tsxmomentum ethernet communications adapter1.jpg

An input base allows us to read proximity switches and buttons around the bender. It has the same form as an output base, but has the unique letters ADI on the right side just below where the communications adapter attaches. We can use 16 point or 32 point input bases. Generally the 32 point bases are less expensive per point.

Tsxmomentum outputbase.jpg



OUTPUT Base

An output base has the same form as an input base, but has the unique letters ADO on the right side just below where the communications adapter attaches. We can use 16 point or 32 point output bases. Generally the 32 point output bases are less expensive per point.

Tsxmomentum outputbase.jpg


Modicon Momentum Analog Base

For applications were we must control the positions of proportional valves to set pressures, we output and hold a specific voltage in the +/-10 volt range using the Modicon Momentum Analog base to output up to 4 separate channels. (We can control four valves with one Analog module.)

Download a datasheet that describes the Analog cards used:
170AAO12000 0..20ma +/-10volt Analog Base

Modicaonmomentum analog.jpg

INPUT Base with Ethernet Communication Adapter

The Ethernet Communications Adapter holds the IP address for this base, and receives the Ethernet cable from a switch or a hub. Each bender is its own small Class C network with addresses like 192.168.0.201, 192.168.0.202, etc.

Tsxmomentum ethernet communications adapter2.jpg


Electrical Panel

Most modules are installed in any order convenient in an electrical panel as shown in this example:

Electricalpanel modicon.jpg



This shows a close-up image of INPUT and OUTPUT modules next to each other in the electrical panel.

Modicon on din.jpg

Other Pages