Difference between revisions of "Mandrel Lube"

From ATTWiki
Jump to: navigation, search
(Test Your Knowledge 3)
(Why Does the Mandrel Lube "Stop Within" Value Work This Way?)
 
Line 63: Line 63:
 
<br><br>
 
<br><br>
  
==Why Does the Mandrel Lube "Stop Within" Value Work This Way?==
+
==Why Does the Mandrel Lube "Stop Angle Within" Value Work This Way?==
  
 
<table>
 
<table>

Latest revision as of 14:04, 31 December 2009

Cncbender logo pushbending.png

Topic: How to Use Mandrel Lube

Mandrel Lube is a powerful feature that is used to precisely control when the lube is injected into the mandrel rod.

Operatorstation model.jpg

Contents


Where is the Mandrel Lube Option?

The lube feature is only available inside the Bend Option cells of the FRB menu. This allows an operator to control mandrel lube for each bend.

Use the Mandrel Lube Enable to switch the feature on or off.

Mandrellubeenable inbendoptions.jpg

Mandrellubeenable.jpg

Mandrel Lube Start and Stop

This feature works with the Mandrel Lube Start and Mandrel Lube Stop angle settings. These control the start and stop of the mandrel lube based upon the bend angle.

The start angle refers to where the lube zone starts: The values is from 0 degrees.

The stop angle refers to where the lube zone ends: The value is an angle that is subtracted from the FINAL ANGLE.

For example, if you set the stop angle to 50 degrees on a 50 degree bend, then the mandrel lube will never start - because CNC Bender is told to stop the lube 50 degrees below the goal - which is 50 minus 50, or 0 degrees.

Mandrellubesetstart.jpg

Mandrellubesetstop.jpg



Why Does the Mandrel Lube "Stop Angle Within" Value Work This Way?

The "stop within" value is always relative to the final bend angle so that if the start and stop values are set to ZERO, then the operator can know for sure that the ENTIRE bend is lubricated - even when the bend angle is adjusted.

We believe that, after the setup technician becomes used to this standard, this makes setup easier.



Press AutoBuild To Make the Changes Take Effect in CNC Processor

Always press AutoBuild in the Bender Data menu for this change to take effect.

Autobuild.jpg


Test Your Knowledge 1

If...

  • the bend angle is 50 degrees
  • the "start angle within" value is 10 degrees
  • the "stop angle within" value is 10 degrees


...how many degrees of bend will the mandrel be lubed?

Answer: 30 degrees

Reason: The lube starts at 10 degrees and stops at 50 minus 10 degrees. So 40-10 = 30 degrees of lube.

Mandrellube diagram startat10degrees.jpg
Mandrellube diagram stopat10under50degrees.jpg

Test Your Knowledge 2

If...

  • the bend angle is 75 degrees
  • the "start angle within" value is 0 degrees
  • the "stop angle within" value is 0 degrees


...how many degrees of bend will the mandrel be lubed?

Answer: 75 degrees

Reason: The lube starts at 0 degrees and stops at 75 minus 0 degrees. So 75-0 = 75 degrees of lube.

Mandrellube diagram startat0degrees.jpg
Mandrellube diagram stopat75degrees.jpg

Test Your Knowledge 3

If...

  • the bend angle is 90 degrees
  • the "start angle within" value is 0 degrees
  • the "stop angle within" value is 90 degrees


...how many degrees of bend will the mandrel be lubed?

Answer: None

Reason: The lube starts at 0 degrees and stops at 90 minus 90 degrees. So 0-0 = 0 degrees of lube.

Mandrellube diagram neverstart90degrees.jpg