View source for Import the Split Bend with STEP Version of "VTube-LASER Demo CAD Model 2"

<table>
<tr cellpadding=10>
<td width=300>
[[image:vtube-step_logo.jpg|300px]]<br>
Import Split Bend in Demo CAD Model 2<br><br>
* Back to [[VTube-LASER]]
* Back to [[VTube-PRO]]
* Back to [[VTube-STEP]]
* See the [[VTube Software Maintenance Plan]] page
</td>
<td width=300>
[[image:Vtube-step_1.77.4.jpg|300px]]
</td>
</tr>
</table>
<br>

__NOTOC__

==Import STEP File==


===Step 1 - Install at least version 3.2 build 778 of VTube-STEP or VTube-LASER===
The STEP version of the Demo Model 2 file is included with this installation.  Also, the collect split bend feature is only available in version 1.79 or newer.<br><br>

===Step 2 - Clear VTube and Import STEP File===
[[image:vtube_opendialog_import_step_model2.jpg]]<br><br>
Clear VTube using the Clear Project icon.  Change to the Import/Export menu and press Import STEP.  The file to import is installed in the C:\Users\Public\Documents\VTube\Demo Files folder by default.  The filename is "VTube-LASER Demo CAD Model 2.stp".
<br><br>

==Make the Tube Transparent==
This is not a required step.  However, when the the tube is transparent you can see if you have collected either the inner or outer diameter.  Selecting both the OD and the ID in various straights will help VTube to extract the OD and the wall thickness at the same time.  (The selection process happens in the "Collection The Tube" process shown in the next section.)

===Step 1 - Load the Entity Control ===
Press the Entity button on the right:<br><br>
[[image:vtube-step_entitymenu1.jpg|300px]]<br><br>
[[image:vtube-step_entitymenu_closeup1.jpg|300px]]<br>
<br><br>

===Step 2 - Select the imported tube ===
In View mode, select the tube with a Window using the mouse and creating a window around the image.<br><br>
[[image:vtube-step_selecttube_model21.jpg|200px]]<br><br>

===Step 3 - Set the Transparency to 0.750 ===
In the Entity Control window Imported Model tab, set the transparency to .750 and press Set.<br><br>
[[image:vtube-step_entitymenu_closeup_750trans_imported1.jpg|200px]]<br><br>
The tube will now appear like this:<br><br>
[[image:vtube_transparent_tube1.jpg|200px]]<br>
<br><br>

==Collect the Tube Straights==
Use these steps to collect the tube straights.  

===Step 1 - Load the Collect Control===
Close the Entity Control window if it is open.  Then open the Collect Control window.<br>
[[image:vtube_collectcontrol1.jpg|300px]]
<br><br>

===Step 2 - Setup and Start the Collection===
In the "Straight from Cylinder SURFACE" tab, check both checkboxes, be sure the straight value is "1", then press the large "Add a Cylinder..." button.<br>
[[image:vtube_collectcontrol_addacylinder_auto1.jpg|150px]]
<br><br>

===Step 3 - Select the Straights 1 Through 4===
Begin selecting straights.  Select straight 1, then 2, then 3, then 4 like this:<br>
[[image:vtube_collectingstraights1-41.jpg|300px]]

===Step 4 - Skip Straight 5 to Select 6===
Skip straight 5 by setting the straight number to 6 in the Collect control.<br>
[[image:vtube_collectcontrol_skipto6.jpg|300px]]

===Step 5 - Select Straights 6 and 7===
Select the rest of the straights.<br>
[[image:vtube_collectcontrol_selectallstraights_demo26.jpg|300px]]
<br><br>

===Step 6 - Setup to Select Split Bend Surface===
Change tabs in the Collect Control to gather the Split Bend Surface:<br>
[[image:vtube_spltbendsurface_straight12.jpg|200px]]<br><br>
Set the straight number to "5" because we are going to select a split bend surface that will build a straight 5.<br>
[[image:vtube_spltbendsurface_straight51.jpg|200px]]<br><br>

===Step 7 - Select The Bend===
Select any part of the bend torus that will give contain points at the extrados apex and the intrados apex:<br>
[[image:vtube_spltbendsurface_selected2.jpg|300px]]<br><br>
In this case, we only need to select one part of the torus to get to both the inside and outside apexes.<br><br>

===Step 8 - Calculate The Centerline===
After collection, press the Rebuild Parametric Tube from Collected button:<br>
[[image:vtube_calculatetubemodel1.jpg|200px]]<br><br>

VTube will ask if you want to Fix Negative Straights and for Split Bends, press '''Yes''' button:<br>
[[image:vtube_calculatetubemodel2.jpg|200px]]<br><br>

==Display Parametric Model==
The new MASTER model will display on the screen - along with the split bend geometry:<br>
[[image:vtube_splitbend_parametric_model3.jpg|400px]]<br><br>
This is the model that should display:<Br>
[[image:vtube_splitbend_parametric_model3_image.jpg|400px]]<br><br>
This is the data that should display:<Br>
[[image:vtube_splitbend_parametric_model3_data.jpg|400px]]<br><br>

==Compress Bender Data for Reporting and Use in VTube-LASER==

===Step 1 - Compress the Bend Data By Switching Split Bend ON ===
The data shown above displays the 4th and 5th bend as two adjacent 90-degree bends in the LRA data.  VTube can compress these two bends into a combined bend to show 180 degrees - which is what the bender will want to see.  Enter the Tube Data menu, press Bend Setup tab, then press the Split Bend Setup button:<br>
[[image:vtube_splitbend_SplitBendSetup_Button.jpg|400px]]<br><br>
This is the Split Bend Setup menu.  It is available in both STEP mode and LASER mode for the MASTER data:<Br>
[[image:vtube_splitbend_window_nosplitbend.jpg|400px]]<br><br>
Change the Split Bend settings so that the 5th straight splits a bend like this:<Br>
[[image:vtube_splitbend_window_splitbend_fifth.jpg|400px]]<br><br>
When you close this window, the bender data will compress like this:<br>
[[image:vtube_splitbend_parametric_model2_data_compressed.jpg|400px]]<br><br>

===Step 2 - Switch to LASER Mode ===
Press the LASER button in the upper right corner of the screen.<br>
[[image:vtube-laser_displayemptyscreen_demomodel2.jpg|400px]]<br><br>


===Step 3 - Display the MASTER Tube in LASER ===
Display the master tube on the screen following these steps:<br>
[[image:vtube-laser_regeneratemastertube_steps.jpg|400px]]<br><br>

[[image:vtube-laser_mastertube_originalview.jpg|400px]]<br><br>

===Step 4 - Orbit the MASTER Tube ===
If necessary, orbit the tube to a good viewing orientation:<br>
[[image:vtube-laser_mastertube_orbitbutton.jpg|400px]]<br><br>
[[image:vtube-laser_mastertube_bestview.jpg|400px]]<br><br>

The master tube is ready for measuring.

==Other==

* Back to [[VTube-LASER]]
* Back to [[VTube-PRO]]
* Back to [[VTube-STEP]]
* See the [[VTube Software Maintenance Plan]] page