Difference between revisions of "How to Setup Reports to Show Bender Plus Adjusted Data"
From ATTWiki
(→Explanation of Why The Values Are Not Negative) |
(→Blue Columns After Bender Values Entered) |
||
(6 intermediate revisions by one user not shown) | |||
Line 15: | Line 15: | ||
<table> | <table> | ||
<tr cellpadding=10> | <tr cellpadding=10> | ||
− | <td width= | + | <td width=500> |
When building reports with bender data plus adjustment data, it is important to remember that the report builder gets the bender data from the Bender Data Setup menu.<br><br> | When building reports with bender data plus adjustment data, it is important to remember that the report builder gets the bender data from the Bender Data Setup menu.<br><br> | ||
Therefore, '''it is critical to enter the Bender Data Setup menu to be sure that the blue column values match the current bender setup before building reports.''' | Therefore, '''it is critical to enter the Bender Data Setup menu to be sure that the blue column values match the current bender setup before building reports.''' | ||
Line 21: | Line 21: | ||
Here is how to use this principle: | Here is how to use this principle: | ||
</td> | </td> | ||
− | <td width= | + | <td width=500> |
</td> | </td> | ||
</tr> | </tr> | ||
Line 38: | Line 38: | ||
</tr> | </tr> | ||
</table> | </table> | ||
+ | <br><br> | ||
==STEP 2 - Adjust the Blue Columns in the Bender Data Setup Menu== | ==STEP 2 - Adjust the Blue Columns in the Bender Data Setup Menu== | ||
Line 45: | Line 46: | ||
VTube builds the adjusted bender data in the reports using the blue columns in the Bender Data Setup menu - not the MASTER LRA data. '''So this step is important even when you are not the Bender Data Setup menu to communicate with the bender.'''<br><br> | VTube builds the adjusted bender data in the reports using the blue columns in the Bender Data Setup menu - not the MASTER LRA data. '''So this step is important even when you are not the Bender Data Setup menu to communicate with the bender.'''<br><br> | ||
− | ===Blue Columns With All Zeros=== | + | ===Blue Columns Start With All Zeros=== |
In this example, the tube has been inspected, '''the but the blue columns are still set to zero''' (see below). The blue columns contain the values that the bender will have before correction. So if the blue columns are all zeros, then the reports will show bender data setup as all zeros + adjustments.<br><br> | In this example, the tube has been inspected, '''the but the blue columns are still set to zero''' (see below). The blue columns contain the values that the bender will have before correction. So if the blue columns are all zeros, then the reports will show bender data setup as all zeros + adjustments.<br><br> | ||
[[image:vtube_benderdatasetup_bluecol_zeros.jpg|600px]]<br><br> | [[image:vtube_benderdatasetup_bluecol_zeros.jpg|600px]]<br><br> | ||
− | ===Blue Columns | + | ===Blue Columns After Bender Values Entered=== |
Fill the blue columns with data either from the MASTER (initial setup), or the actual data used in the bender.<br><br> | Fill the blue columns with data either from the MASTER (initial setup), or the actual data used in the bender.<br><br> | ||
* To copy the Master data, use the "COPY Master LRA to Setup LRA" button.<br><br> | * To copy the Master data, use the "COPY Master LRA to Setup LRA" button.<br><br> | ||
* To enter actual data from the bender, either press the RECALL LRA from BENDER if your bender has a connection, or enter the data in the blue columns manually.<br><br> | * To enter actual data from the bender, either press the RECALL LRA from BENDER if your bender has a connection, or enter the data in the blue columns manually.<br><br> | ||
+ | * Filling the blue columns with values will change correction reports.<br><br> | ||
[[image:vtube_benderdatasetup_bluecol_nonzeros.jpg|600px]] | [[image:vtube_benderdatasetup_bluecol_nonzeros.jpg|600px]] | ||
Latest revision as of 05:24, 22 September 2012
Setup VTube-LASER Reports to Show Bender Plus Adjusted Data
|
Contents |
When building reports with bender data plus adjustment data, it is important to remember that the report builder gets the bender data from the Bender Data Setup menu. |
STEP 1 - Measure and Align
Enter the MASTER data, then measure and align the measured tube to the master data. |
STEP 2 - Adjust the Blue Columns in the Bender Data Setup Menu
STEP 3 - Exit the Bender Data Setup Menu to Display Reports
Example Effect on Report with Incorrect/Correct Setup of Bender Data
Other Pages
- Back to VTube-LASER