How Do I Install CNC Bender On a New Computer?

From ATTWiki
Revision as of 19:23, 22 April 2010 by Mcone (Talk | contribs)

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search
Cnclaptop.jpg



Contents

DESIGN

CNC Bender is designed to be easy to setup on most computers in your office . Nearly any Windows computer with a TCP/IP connection will work.

This means that you can run CNC Bender on nearly any laptop or desktop computer in your office. See the steps below for step by step instructions on how to install CNC Bender to any compatible computer.



LICENSE

What about licensing requirements? Our licensing requirements are very simple because the license is tied to a device we call a hardware key. If you have the hardware key, then you are permitted to run CNC Bender. This means that you can copy CNC Bender software to as many computers as you wish. In fact, I recommend that you make at least one working backup copy for emergency recovery.



HOW TO INSTALL CNC BENDER to A NEW COMPUTER

Follow these steps to setup CNC Bender on your new computer.


STEP 1



Close CNC Bender

Close CNC Bender software on the operator station that you want to duplicate.

CNC Bender Software

STEP 2



USB Flash Drive

Plug a USB FLASH DRIVE[1] into the operator station USB port (inside the enclosure). (You will need a FLASH DRIVE with about 100 Megabytes of free memory.)
USB Flash Drive

STEP 3



Find CNC Folder

Browse to the C:\CNC folder on the operator station using Windows Explorer.

STEP 4



Copy CNC Folder

Copy the CNC FOLDER to the USB flash drive.

STEP 5



Remove the USB Flash Drive

Remove the USB flash drive using the system tool tray "Safely Remove Hardware" feature.

STEP 6



Plug the USB Flash Drive In

Plug the USB flash drive into the NEW target computer.

STEP 7



Copy to C:\CNC

Use Windows Explorer to copy the data to the same folder on the target computer's drive. The folder should be "c:\cnc"

STEP 8



Run the Hardware Key DRIVER

HASP Driver Software

Browse to the c:\cnc\key folder and run "hdd32.exe." This program is a hardware key driver file that needs only to be run once. It may require that you be logged in as a user with administrative rights.

Download the latest hdd32.exe file here: http://www.advancedtubular.com/key/hdd32.exe

STEP 9



Transfer Hardware Key

Hasp Hardware Key

Remove the hardware key from the USB port of the CNC Bender operator station (inside the operator station enclosure).

Plug it into the new computer's USB port.

STEP 10



Set the NEW Computer IP Address

Use the Windows Start / Connect To menu to configure the TCP/IP address of the port that will connect to the bender. Set that port to a fixed IP address of 192.168.0.199. Any valid setting under 200 for the last octet will work. The operator station uses .200 as the address. If the operator station is not powered on, or is not attached to the bender network, then you can also use address .200.

STEP 11



Plug Ethernet

Plug an ethernet cable (RJ45 type) between the new computer's NIC port and the Netgear switch in the electronics cabinet using a standard ethernet cable.
Netgear Switch

STEP 12



CNC Bender Software

Start CNC Bender software by finding the CNCBender.exe program in the c:\cnc folder and double clicking on it (or select the file and press Enter).

CNC Bender Software


From this point, operation of CNC Bender is identical to the operation of CNC Bender on the operating station. The physical buttons on the operator station are still needed to operate the bender. The replacement computer should probably be placed near the operator station.

Note: Since the operator station is completely powered down, the touchscreen is no longer used while using the backup computer. Use the mouse on the new computer to simulate the touchscreen.




SOUND SYSTEM

Auditory sound messages are an important part of knowing the state of the bender control. I recommend that you be sure to use a computer with a sound system for operating CNC Bender sofware.

--Mcone 13:07, 5 March 2007 (EST)