Difference between revisions of "DCF - Dual Cylinder Fit"

From ATTWiki
Jump to: navigation, search
(How It Works)
(How It Works)
Line 26: Line 26:
 
When using the LASER scanner, the UNISCAN DCF feature divides the cylinder surface data into two groups, then calculates the cylinder data and intersection points twice to verify repeatability. (Note that this feature is not used tactile measurements.)
 
When using the LASER scanner, the UNISCAN DCF feature divides the cylinder surface data into two groups, then calculates the cylinder data and intersection points twice to verify repeatability. (Note that this feature is not used tactile measurements.)
 
<br><br>
 
<br><br>
The Point Repeatability value (see "check 4" below) is reported in the Cylinder Fit window. If this value is too high, then VTube-LASER will warn you. This allows you to remeasure the straight to guarantee that the measure repeats before moving to the next straight.<br><br>
+
The Point Repeatability value (see '''CHECK 4''' below) is reported in the Cylinder Fit window. If this value is too high, then VTube-LASER will warn you. This allows you to remeasure the straight to guarantee that the measure repeats before moving to the next straight.<br><br>
 
<td>
 
<td>
 
</td>
 
</td>

Revision as of 23:01, 22 April 2017

Contents

About the Feature

Vtube-laser v2.8 cylinderfit DualCylinderFit.png

DCF is the major enhancement for VTube-LASER in version 2.8 (April 19, 2017) because it replicates measuring the tube TWICE in one pass without the user noticing.


This method helps to ensure repeatability of the cylinder measurements on-the-fly using a LASER scanner.

Click on the image below to see the introductory video:

Vtube-laser v2.8 dualcylinderfit intro video.png

Vtube-laser v2.8 DCF logo.png



How It Works

When using the LASER scanner, the UNISCAN DCF feature divides the cylinder surface data into two groups, then calculates the cylinder data and intersection points twice to verify repeatability. (Note that this feature is not used tactile measurements.)

The Point Repeatability value (see CHECK 4 below) is reported in the Cylinder Fit window. If this value is too high, then VTube-LASER will warn you. This allows you to remeasure the straight to guarantee that the measure repeats before moving to the next straight.

Vtube-laser v2.8 DualCylinderFit model.png

Vtube-laser v2.8 DualCylinderFit model step3.png



MULTIPLE LEVELS OF CYLINDER FIT CHECKS

As part of the DCF feature, the Cylinder Fit Data window reports cylinder fit values that help you know if the cylinder measurement is good.

When using Uniscan mode, VTube cylinders must pass a total of FOUR checks to be qualified as good cylinder scans.

CHECK 1 - MAXIMUM WOBBLE PREDICTION

The Maximum Wobble value predicts how precise the surface data fits the cylinder. This was in previous versions, but now two cylinders must pass - not just one. And we've created a single new value to display at the top rather than multiple XY values.

CHECK 2 - OD SURFACE TO CENTERLINE

The new OD Surface to Centerline value reports the low and high points on the measured diameter relative to the centerline. If the values get too far from each other (the "Delta"), then VTube-LASER will warn you. Also, the Out-of-round% is reported and used to qualify the cylinder fit. This is active for both LASER and ball probe.

CHECK 3 - INTERSECTION PASS DISTANCE

The Intersection Pass Distance shows how near each intersecting 3D centerline comes to each other in 3D space. If the Nearest Pass value is more than the Intersection Error Tolerance, then VTube-LASER will warn you. This is active for both LASER and ball probe.

CHECK 4 - DUAL CYLINDER FIT

As mentioned above, because the DCF engine creates two cylinders, it always builds and compares the resulting intersection points from both cylinders. It warns you if they don't match well enough.

Vtube-laser v2.8 cylinderfit window sections.png