Difference between revisions of "Change the default linear units in VTube"

From ATTWiki
Jump to: navigation, search
(25px Steps to changing the default linear units)
 
(12 intermediate revisions by one user not shown)
Line 4: Line 4:
 
[[image:vtube-step_logo.jpg|200px]]<br>
 
[[image:vtube-step_logo.jpg|200px]]<br>
 
[[image:vtube-laser_logo.jpg|200px]]
 
[[image:vtube-laser_logo.jpg|200px]]
==Revision 1.65==
 
 
* Back to [[VTube-STEP]]
 
* Back to [[VTube-STEP]]
 
* Back to [[VTube-LASER]]
 
* Back to [[VTube-LASER]]
 
</td>
 
</td>
 
<td width=300>
 
<td width=300>
[[image:Vtube-step_1_65.jpg|300px]]
+
[[image:Vtube-step_1_651.jpg|300px]]<br>
 +
[[image:vtube-laser_screen_1_541.jpg|300px]]
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 25: Line 25:
 
Use the toolbar buttons to clear VTube and press the Linear Units button until the correct units are active.</td>
 
Use the toolbar buttons to clear VTube and press the Linear Units button until the correct units are active.</td>
 
<td>
 
<td>
[[image:vtube-step_toolbar_sys.jpg|300px]]
+
[[image:vtube-step_toolbar_clear_units1.jpg|600px]]
 
</td>
 
</td>
 
</tr>
 
</tr>
Line 32: Line 32:
 
Press the System Options button.</td>
 
Press the System Options button.</td>
 
<td>
 
<td>
[[image:vtube-step_toolbar_sys.jpg|300px]]
+
[[image:vtube-step_toolbar_sys1.jpg|400px]]
 
</td>
 
</td>
 
</tr>
 
</tr>
 +
<tr>
 +
<td width=300>
 +
Press the Project Setup tab, and then press the Set Project Default State button.</td>
 +
<td>
 +
[[image:vtube-step_setprojdefaultstate1.jpg|400px]]
 +
</td>
 +
</tr>
 +
 +
<tr>
 +
<td width=300>
 +
Exit the System Options menu.  VTube will now clear to the new linear unit.
 +
</td>
 +
<td>
 +
</td>
 +
</tr>
 +
 
</table>
 
</table>
 
<br>
 
<br>
Line 40: Line 56:
 
==Other Pages==
 
==Other Pages==
  
*Back to the [[VTube]] page
+
*Back to the [[VTube-STEP]] page
 +
*Back to the [[VTube-LASER]] page

Latest revision as of 14:23, 25 May 2022

Vtube-step logo.jpg
Vtube-laser logo.jpg

Vtube-step 1 651.jpg
Vtube-laser screen 1 541.jpg



Check.jpg Steps to changing the default linear units

Use the toolbar buttons to clear VTube and press the Linear Units button until the correct units are active.

Vtube-step toolbar clear units1.jpg

Press the System Options button.

Vtube-step toolbar sys1.jpg

Press the Project Setup tab, and then press the Set Project Default State button.

Vtube-step setprojdefaultstate1.jpg

Exit the System Options menu. VTube will now clear to the new linear unit.


Other Pages