Difference between revisions of "CRIPPA"

From ATTWiki
Jump to: navigation, search
(VTube-LASER Support for Crippa Bender Setup and Corrections)
(VTube-LASER Support for Crippa Bender Setup and Corrections)
 
(30 intermediate revisions by one user not shown)
Line 12: Line 12:
 
</table>
 
</table>
  
==CRIPPA UII Control software==
+
==CRIPPA UII Control software Version 3==
 
<table width=700>
 
<table width=700>
 
<tr>
 
<tr>
 
<td>
 
<td>
The CRIPPA Windows software allows for complete programming of bender setup.
+
The CRIPPA Windows software allows for complete programming of bender setup.<br><br>
 +
This is an older version 3.2 of the CRIPPA UII.
 
</td>
 
</td>
 
<td>
 
<td>
Line 23: Line 24:
 
</tr>
 
</tr>
 
</table>
 
</table>
 +
 +
==CRIPPA UII Control software version EVO II==
 +
<table width=700>
 +
<tr>
 +
<td>
 +
This is the screen from the Evo II generation of Crippa UII software (circa 2017). Changes made by VTube-LASER can be viewed in the YBC grid on this page.<br><br>
 +
</td>
 +
<td>
 +
[[image:crippa_520_uii_screen_evoII.png|400px]]
 +
</td>
 +
</tr>
 +
 +
<tr>
 +
<td>
 +
This is the main screen for the CRIPPA HMI.  The UII screen (shown above) is loaded from the bottom toolbar button in this screen.<br><br>
 +
</td>
 +
<td>
 +
[[image:crippa_evoII_hmi_point_to_UIIbutton.png|400px]]
 +
</td>
 +
</tr>
 +
 +
</table>
 +
 +
 
<br><br>
 
<br><br>
  
Line 29: Line 54:
 
<tr>
 
<tr>
 
<td width=300 valign=top>
 
<td width=300 valign=top>
VTube-LASER communicates with the CRIPPA UII software using the Supravision Network protocol.<br><br>
+
[[VTube-LASER]] communicates with the newer CRIPPA UII software using the Supravision Network protocol.<br><br>
 
Communications are fully bidirectional - you can send and recall data.<br><br>
 
Communications are fully bidirectional - you can send and recall data.<br><br>
 
It is possible to send new part data to the Crippa, and to correct existing parts easily with the Crippa communications.<br><br>
 
It is possible to send new part data to the Crippa, and to correct existing parts easily with the Crippa communications.<br><br>
(Crippa added this capability in late 2014.)
+
(Crippa added this capability in late 2014.) See [[VTube Communication for CRIPPA Supravision]] for details.<br><br>
 +
[[VTube-LASER]] can also communicate with older CRIPPA SIEMENS SINUMERIK controls by building the CRIPPA MPF data files. See [[VTube Communication for CRIPPA MPF]] for details.
 
</td>
 
</td>
 
<td width=500>
 
<td width=500>
Line 43: Line 69:
 
<br><br>
 
<br><br>
  
==Success Story for a Customer that uses [[VTube-LASER]] with a CRIPPA Bender==
+
==[[VTube-STEP]] Support for Newer CRIPPA Bender SPF Files==
<table width=900 cellpadding=10>
+
  
<tr>
+
<table cellpadding=10>
<td width=400 valign=top>
+
<tr valign=top>
<font size="4">Aerospace Welding, Inc.</font>, is a Montreal-based fully-certified fabrication company for major aerospace companies.<br><br>
+
<td width=300>
</td>
+
For newer benders, [[VTube-STEP]] can export Crippa export capability allows for easy export to Crippa UII software.  The format is a text file that is compatible with most CRIPPA benders that were released in early 2012 and on.<br><br>
<td>
+
[[image:vtube_step_1.77.4_crippa_export.jpg|400px]]<br><br>
[[image:logo_dcm_aerospace_2.png|200px]]
+
</td>
+
</tr>
+
 
+
<tr>
+
<td width=400 valign=top>
+
They use VTube-LASER running on a FARO arm to setup and correct an all electric CRIPPA bender.<br><br>
+
During their initial training sessions, the customer bent a part on the bender based on the nominal setup data that was entered into VTube-LASER, then transferred to the bender.<br><br>
+
The operator used VTube-LASER on a FARO arm to measure and prove that the part had a maximum deviation of 0.060" of deviation along the centerline profile.  The centerline profile tolerance, per the print, was from 0.030 inches up to 0.050 inches for this aerospace part - so it was necessary to send a correction to the bender.<br><br>
+
The first correction reduced the profile deviations so that only one deviation peaked at 0.012 inches.  All the other deviations where half that value or better.  The End-A length deviation was literally 0.000 inches, and the bending technician trimmed the other end using the "End-B Trim" value in the VTube-LASER inspection page.  He remeasured the final part which was confirmed to be completely inside tolerance.<br><br>
+
Aerospace Welding is very happy with this system.<br><br>
+
===Customer Contact Information===
+
Nino Buttino, Directeur Commercial (Commercial Director)<br>
+
Aerospace Welding, Inc.<br>
+
Phone: (450) 435-9210 x2223<br>
+
Address: 890 Blvd. Michelle-Bohec,<br>Blainville, QC J7C 5E2, Canada<br>
+
website: http://www.aerospacewelding.com
+
 
</td>
 
</td>
 
<td width=500>
 
<td width=500>
[[image:vtube-laser_v2.2_aerospace_welding.png|500px]]
+
[[image:VTS2_SplashScreen.png|500px]]
 
</td>
 
</td>
</tr>
+
</tr>  
 
</table>
 
</table>
  
 
+
==[[VTube-STEP]] Support for Legacy CRIPPA Bender MPF Files==
<br><br>
+
 
+
==[[VTube-STEP]] Support for CRIPPA Bender SPF Files==
+
  
 
<table cellpadding=10>
 
<table cellpadding=10>
 
<tr valign=top>
 
<tr valign=top>
 
<td width=300>
 
<td width=300>
[[VTube-STEP]] can export Crippa export capability allows for easy export to Crippa UII software.  The format is a text file that is compatible with most Crippa benders that were released in early 2012 and on.<br><br>
+
For older CRIPPA SIEMENS SINUMERIK benders, VTube-STEP can build MPF files. (As of VTube version 2.7, December of 2016)<br><br>
[[image:vtube_step_1.77.4_crippa_export.jpg|400px]]<br>
+
See [[VTube Communication for CRIPPA MPF]] for details.<br><br>
 
+
[[image:vtube-step_2.7 export crippa mpf.png|400px]]<br><br>
  
 
</td>
 
</td>
Line 106: Line 111:
  
 
==Other Pages==
 
==Other Pages==
* See the [http://www.crippa.com/pagine/prodotti/curvatubi/curvatubi_presentazione_ing.asp Crippa Web Site]
 
 
* See [[VTube-LASER]]
 
* See [[VTube-LASER]]
 
* See [[VTube-STEP]]
 
* See [[VTube-STEP]]
 +
* See [[VTube Communication for CRIPPA MPF]] for a tutorial on communications setup and use

Latest revision as of 14:58, 11 August 2017


CRIPPA benders are built in Italy and marketed worldwide. Customers report that they like these benders very much. They are often all electric with all actuators servo-controlled.

Crippa bender.jpg

Crippa banner.jpg

Contents

CRIPPA UII Control software Version 3

The CRIPPA Windows software allows for complete programming of bender setup.

This is an older version 3.2 of the CRIPPA UII.

Crippa uii screen.jpg

CRIPPA UII Control software version EVO II

This is the screen from the Evo II generation of Crippa UII software (circa 2017). Changes made by VTube-LASER can be viewed in the YBC grid on this page.

Crippa 520 uii screen evoII.png

This is the main screen for the CRIPPA HMI. The UII screen (shown above) is loaded from the bottom toolbar button in this screen.

Crippa evoII hmi point to UIIbutton.png




VTube-LASER Support for Crippa Bender Setup and Corrections

VTube-LASER communicates with the newer CRIPPA UII software using the Supravision Network protocol.

Communications are fully bidirectional - you can send and recall data.

It is possible to send new part data to the Crippa, and to correct existing parts easily with the Crippa communications.

(Crippa added this capability in late 2014.) See VTube Communication for CRIPPA Supravision for details.

VTube-LASER can also communicate with older CRIPPA SIEMENS SINUMERIK controls by building the CRIPPA MPF data files. See VTube Communication for CRIPPA MPF for details.

Vtube-laser v2.2 crippa.png




VTube-STEP Support for Newer CRIPPA Bender SPF Files

For newer benders, VTube-STEP can export Crippa export capability allows for easy export to Crippa UII software. The format is a text file that is compatible with most CRIPPA benders that were released in early 2012 and on.

Vtube step 1.77.4 crippa export.jpg

VTS2 SplashScreen.png

VTube-STEP Support for Legacy CRIPPA Bender MPF Files

For older CRIPPA SIEMENS SINUMERIK benders, VTube-STEP can build MPF files. (As of VTube version 2.7, December of 2016)

See VTube Communication for CRIPPA MPF for details.

Vtube-step 2.7 export crippa mpf.png

VTS2 SplashScreen.png

Contact Information

CRIPPA USA Distributor

Chris Harrison
Tube Process Technology LLC
4343 SKUSA DR
BRIGHTON, MI 48116

Phone (810) 599-1972
E-Mail: [email protected]

Other Pages