CNC Bender ProControl 10-20070330

From ATTWiki
Revision as of 16:58, 3 April 2007 by Mcone (Talk | contribs)

Jump to: navigation, search
CNC Bender 10-20070331 Splash.jpg

Contents


REVISION Information

10-20070330, March 30, 2007


REPAIRED: Pressure Die Boost Issue

The Degrees from Goal value was acting as if it were the Degrees from Start value. This has been repaired.




NEW: Servo Module Programmable Switch Logic is now Controllable

The I2T Servo Module is used on CNC Bender systems have a feature called "Programmable Limit Switch". A programmable limit switch is controlled by two positions along or around an axis. The first position is the LOW and the second position is the HIGH. The low and high values are floating point values. There are eight programmable limit switches per servo axis. The first use of this feature is the Tube-Support Up/Down setting. See the Tube-Support Location section for an example and details for how to use the programmable limit switch values.




NEW: Tube Support Location is now Programmable

The tube-support up/down location relative to the Feed axis can now be changed at the CNC Bender operator station. It is changed in the InitAxes processlist in the Low Level menu. Every time the axes are initialized, CNC Bender sets this value. It can be changed by adjusting the COMDEF line: FeedAxisPLS5 = LSL0:0, LSU0:1500

The LSL parameter is reserved for the Limit Switch Lower value. This is where the output for the tube support switches to active. The appropriate value is usually a Feed axis value of 0 units (millimeters). The LSU parameter is reserved for the Limit Switch Upper value. The appropriate value is the position to control at which forward feed position the tube support begins to drop. The value is always indicated in millimeters. Floating point values are allowed. The integer value after the LSL or LSU indicates the index position of the CIO inside the COMDEF. In this case, the index is 0, which is the first position in the list of CIO objects.

The CIO object is a SERVO MODULE COMMAND. The Modbus OpCode for setting programmable limit switches is 2013 for the first axis in a card, and 2014 for the second axis in a card. See the CIO library's "FeedAxisPLS5" CIO object to see how to setup a new CIO that an address any programmable limit switch. The first word value controls which output to address:

Word 1 value...
- is 0 to set output 1
- is 1 to set output 2
- is 2 to set output 3
- is 3 to set output 4
- is 4 to set output 5
- is 5 to set output 6
- is 6 to set output 7
- is 7 to set output 8

Words 2 and 3 are set aside for the low value. The LSL parameter stuffs values into these two words in a process list line. Words 4 and 5 are set aside for the high value The LSU parameter stuffs values into these two words in a process list line.

Ciodictionary opcode 2013 setup.jpg

The programmable limit switch values can be monitored using the I2T Module Interface software. Use the Programmable Limit Switches feature.

I2t moduleinterface pls axis1.jpg




NEW: Feed-Bend Motion Adjust Percent For EACH Radius Level

This feature was available as a single value for all bend radius levels. Now a unique Feed-Bend Motion Adjust Percent for each radius level is available. This will allow for different elongation on the different dies on the same job. These new options are in the Overall Bending Options menu of the BENDING tab menu.

Feed-bend motion adjust multiple radii.jpg


Feed-Bend Motion Adjust %



Floating Point Value

Feed Bend Motion Adjust Percent Closeup.jpg

Using a Value of ZERO



A value of ZERO will cause no adjustment in the Feed motion during Feed Bending.

Using a Value BELOW ZERO



For example, enter -5 (negative 5) to adjust the Feed motion during Feed bending by negative 5 percent.

Use this value will accomodate for...


  1. Extreme elongation that cause the Feed axis to jump after the motion is complete and the bend dies open. (Larger/stiffer tubes)
  2. Bowing of the smaller diameter tubes.

Decreasing the value too much will likely cause the tube to pull from the chuck.

Using a Value of ABOVE ZERO



For example, enter 5 (positive 5) to move 5 percent further during Feed Bending..

Increasing the value too much will cause the Feed to attempt to press further for final position, not allowing it to come into position.




NEW: Radius Level Selection Dialog

This feature makes it easier to switch bend radius levels in the MANUAL page.

Cncbender radiuslevel selection.jpg


NEW: SetDefaultJogSpeeds now Receives Velocity Parameters

The SetDefaultJogSpeeds command controls the DIRECT AXIS JOG SPEEDS for the MANUAL page. Before this version the SetDefaultJogSpeeds COMDEF could not take in parameters. All values were only controllable in the CIO Dictionary setup software. Now, the value can be adjusted in the InitAxes Run tab in the Low Level menu. The axis speeds are addressed in order of axis number, Feed, Rotate, Bend, Horizontal Shift:

SetDefaultJogSpeeds = vel0:75, vel1:20, vel2:5, vel3:50

Note: Sending parameters to any jog speed COMDEF BEFORE this version of CNC Bender will cause an error.


InitAxes Runnn SetDefaultJpgSpeeds.jpg




ENHANCED: CNC Processor Log Much Faster

The processor log in the Processor menu of CNC Bender was optimized to be several times faster than previous version logs. This removes a potential bottleneck jam for information being passed from CNC Processor to CNC Bender.

Cncbender processor log.jpg




NEW: Added the COMDEF/CIO Tab Menu in Low Level

This new menu allows operators to quickly load either the COMDEF Dictionary Editor or CIO Dictionary Editor from within CNC Bender.

Cncbender comdef cio menu.jpg