|
|
| (One intermediate revision by one user not shown) |
| Line 3: |
Line 3: |
| | | | |
| | | | |
| − | ===Connect to [[EL Vector Tube Data Center]]s Using Current Loop Electronics===
| + | * [[Benderlink Ethernet Module Cable Reference]] |
| − | The module can even be equipped with our version of the Eaton Leonard current loop boards (our own model called the [[CB-EL1]]) to allow for 100% compatible Eaton Leonard legacy protocol through the network for connection to an [[EL Vector Tube Data Center]]<br><br>
| + | |
| | | | |
| − | <table>
| |
| − | <tr>
| |
| − | <td width=200>This module comes in either wireless or Wired Benderlink Ethernet Module</td>
| |
| − | <td>
| |
| − | [[image:blink_ethernet_module_vector_benderside_600.jpg|350px]]
| |
| − | </td>
| |
| − | </tr>
| |
| − | <tr>
| |
| − | <td width=200>This is the same module with cables in place. Three cables are attached to the wired version. A fourth wireless antenna cable is attached for wireless version.
| |
| − | </td>
| |
| − | <td>
| |
| − | [[image:blink_ethernet_module_vector_benderside_cables_600.jpg|350px]]
| |
| − | </td>
| |
| − | </tr>
| |
| | | | |
| − | </table>
| + | ==Other Pages== |
| | | | |
| − | | + | *[[Benderlink Ethernet Module]] |
| − | Examples:
| + | |
| − | {| border="0" cellpadding="10" cellspacing="0" align="none" width=500
| + | |
| − | |-
| + | |
| − | ! style="background:#b3b0c8;" | Bender
| + | |
| − | ! colspan="2" style="background:#acbcce;" | Description
| + | |
| − | |-
| + | |
| − | | PINES TS-2000
| + | |
| − | | Using [[Benderlink for Pines]] - Add a module to a [[Vector Tube Data Center]] to enable a network connection through a current-loop module directly into the standard Vector bender port.
| + | |
| − | |-
| + | |
| − | | [[BLM]] [[VGP]]
| + | |
| − | | Using [[Benderlink for BLM]] - Add a module to [[Vector Tube Data Center]] to enable a network connection through a current-loop module directly into the standard Vector bender port.
| + | |
| − | |-
| + | |
| − | | ROMER to Eaton Leonard
| + | |
| − | | Add a module to any Eaton Leonard bender and make it wireless.
| + | |
| − | |-
| + | |
| − | | CHIYODA
| + | |
| − | | Add this module to a Chiyoda to allow it to communicate over the network from its RS-232 port.
| + | |
| − | |-
| + | |
| − | | KEINS
| + | |
| − | | Add this module to a KEINS to allow it to communicate over the network from its RS-232 port.
| + | |
| − | |-
| + | |
| − | | MiiC
| + | |
| − | | Works with a MiiC to place it on the network (See [[Benderlink for MiiC]])
| + | |
| − | |}
| + | |
| − | | + | |
| − | ==PDF DataSheets==
| + | |
| − | | + | |
| − | | + | |
| − | <table cellpadding="15" width = 650>
| + | |
| − | <tr valign="top">
| + | |
| − | <td bgcolor="#abbad1" width = 200>
| + | |
| − | [[image:Blinkel_ethernet_module_datasheet_page1.jpg|200px]]
| + | |
| − | </td>
| + | |
| − | <td bgcolor="#e3e4f5">
| + | |
| − | [http://www.advancedtubular.com/blink_el/benderlink_el_ethernet_module_datasheet.pdf Download a DataSheet] for Benderlink Ethernet Module for Eaton Leonard
| + | |
| − | | + | |
| − | <br><br>
| + | |
| − | [http://www.advancedtubular.com/blink_chi/blinkchi_module_datasheet.pdf Download a DataSheet] for Benderlink Ethernet Module for
| + | |
| − | Chiyoda
| + | |
| − | | + | |
| − | <br><br>
| + | |
| − | [http://www.advancedtubular.com/blink_pines/blinkpines2vector_module_datasheet.pdf Download a DataSheet] for Benderlink Ethernet Module for PINES to Vector 1
| + | |
| − | | + | |
| − | | + | |
| − | </td>
| + | |
| − | </tr>
| + | |
| − | </table>
| + | |
