VTube-LASER v2.8

From ATTWiki
Revision as of 19:16, 18 April 2017 by Mcone (Talk | contribs)

Jump to: navigation, search

Vtube-laser logo 1.96.png


Revision 2.8

Release Date: Not Released Yet


Vtube-laser v2.7 screenshot.png

Contents


BUILD 44 - April 11, 2017

Check.jpg NEW: UNISCAN DCF (DUAL CYLINDER FIT) Feature

Vtube-laser v2.8 cylinderfit DualCylinderFit.png

DCF is the major enhancement for VTube-LASER in version 2.8 because it replicates measuring the tube TWICE in one pass without the user noticing.


This method helps to ensure repeatability of the cylinder measurements on-the-fly using a LASER scanner.


When using the LASER scanner, the UNISCAN DCF feature divides the cylinder surface data into two groups, then calculates the cylinder data and intersection points twice to verify repeatability. (Note that this feature is not used tactile measurements.)

The Point Repeatability value is reported in the Cylinder Fit window. If this value is too high, then VTube-LASER will warn you. This allows you to remeasure the straight to guarantee that the measure repeats before moving to the next straight.

Vtube-laser v2.8 DualCylinderFit model.png

Vtube-laser v2.8 DualCylinderFit model step3.png



Check.jpg NEW: ADDED 3 NEW CYLINDER FIT CHECKS

This window reports cylinder fit values that help you know if the cylinder measurement is good.

When using Uniscan mode, VTube cylinders must now pass a total of FOUR checks to be qualified as good cylinder scans.

CHECK 1 - MAXIMUM WOBBLE PREDICTION

The Maximum Wobble value predicts how precise the surface data fits the cylinder. This was in previous versions, but now two cylinders must pass - not just one. And we've created a single new value to display at the top rather than multiple XY values.

CHECK 2 - OD SURFACE TO CENTERLINE

The new OD Surface to Centerline value reports the low and high points on the measured diameter relative to the centerline. If the values get too far from each other (the "Delta"), then VTube-LASER will warn you. Also, the Out-of-round% is reported and used to qualify the cylinder fit. This is active for both LASER and ball probe.

CHECK 3 - INTERSECTION PASS DISTANCE

The Intersection Pass Distance shows how near each intersecting 3D centerline comes to each other in 3D space. If the Nearest Pass value is more than the Intersection Error Tolerance, then VTube-LASER will warn you. This is active for both LASER and ball probe.

CHECK 4 - DUAL CYLINDER FIT

As mentioned above, because the DCF engine creates two cylinders, it always builds and compares the resulting intersection points from both cylinders. It warns you if they don't match well enough.

Vtube-laser v2.8 cylinderfit window sections.png



Check.jpg NEW: CYLINDER FIT WINDOW is NOW COLOR-CODED

The window is now color-coded to help you quickly determine where the problem lies in the data.

RED PANEL

This would indicate a major problem in the cylinder fit calculation. VTube requires a remeasure of a straight section.

Vtube-laser v2.8 cylinderfitwindow redpanel.png



GREEN PANEL

All green indicates that no issues were found in all four checks. You can trust the calculation.

Vtube-laser v2.8 cylinderfitwindow greenpanel.png



Intersection Pass Distance Warning Test

This is an example of the Intersection Pass Distance warning test.

Vtube-laser v2.8 IntersectionPassDistance.png



Check.jpg NEW: Automatic ORBIT to TRUE VIEW of MEASURED CYLINDERS

We teach users to view the end scan on the screen before moving to the step. In previous versions, this required that you manually orbit the viewport so that you can see the end scans.

From this version forward, VTube automatically orbits every straight TRUE to the screen so that you don't have to use the mouse to find that orientation.

Vtube-laser v2.8 automatic truecylinders.png



Check.jpg NEW: CONFIGURE CYLINDER FIT TOLERANCES ON-THE-FLY

Users can now easily configure cylinder fit tolerances on-the-fly.

If a tolerance is too tight for a tube straight that has a lot of deformation, then you can easily increase the tolerance at any time.

Vtube-laser v2.8 CylinderFit GearButton.png




Check.jpg NEW: CONFIGURE CYLINDER FIT QUALIFICATION VALUES

This a new group of qualification values in the Measure 1 tab menu of System Options. Most of these values are new to the VTube-LASER project file storage.

Vtube-laser v2.8 new cylinder fit qualification values.png




Check.jpg NEW: Point Labels for All Models

This version now shows point labels for all models drawn on the screen.

Vtube-laser v2.8 point labels for all models.png




Check.jpg NEW: ORBIT CONTROL Window

This window lets you find any true or normal orientation for any line or bend in any model.

Click on the image below to see a video:

Vtube-laser v2.8 orbitcontrolwindow video.png

Vtube-laser v2.8 orbitcontrolwindows.png



Check.jpg NEW: Redesigned Parametric Display Options Window

The Parametric Display Options Window has been redesigned to include model colors and easier to use controls.

Vvtube-laser v2.8 parametricdisplayoptions.png




Check.jpg NEW: Import TUBE DATA from ROMER CIMCORE DOCS .DS FILES

Import DOCS tube data in VTube-STEP mode.

VTube-STEP v2.8 ImportDOCS.png



BUILD 20 - March 14, 2017

Check.jpg NEW: MantisHub Web Server Bug Tracking

This version of VTube will allow you to choose to report software errors directly to our account at MantisHub.

This service will allow us to track bug issues with VTube-STEP and VTube-LASER.

MantisHubLogo.png



BUILD 11 - February 15, 2017

Check.jpg NEW: "Default Tolerance Ends" Value

The Default Tolerance Ends value is in the Inspection Data menu.

It allows you to set the end length default values separately from the tangent point / midpoint tolerance values.

Vtl-v2.8 Default End Tolerance.png




Check.jpg NEW: REPORT COMMANDS - Tangent Deviation AVERAGE and MAXIMUM Values

Two new array values are available for reports: AVERAGE deviation and MAXIMUM deviation.

The new commands are

  • array_dev_tmt_average
  • array_dev_tmt_maximum



See the example result in the report on the right, and the report template source to create this table shown below.

Vtl-2.8 inspection data tangent average and maximum html sample.png




Vtl-2.8 inspection data tangent average and maximum.png



BUILD 19 - February 22, 2017

Check.jpg ENHANCED: Winton WMC Communications Improvement

The process for corrections to Winton WMC files were clarified with dialogs that make it very clear what VTube-LASER Bender Setup is doing during the Winton WMC correction process.

Winton bender.png

1 - NEW HELP DIALOGS

Steps 2 and 5 are new. They carefully explain what is happening during the correction process.

2 - NEW BACKUP CREATED

Step 5 also explains that a BACKUP file is created during the process. This allows operators to always recover to the previous data if something goes wrong in the correction process. (The creation of a backup file is new in this version.)

Immediately after the user presses the Auto Correction button, this dialog appears (see step 2 below):

Vtl v2.8 winton correction existing dialog.png

Immediately after the user presses the Exit and Save setup data button, this dialog appears (see step 4 below):

Vtl v2.8 winton correction overwrite backup dialog.png




New Process Flow for Winton WMC Correction

This image shows the overall process for correction of Winton WMC files.

Vtl v2.8 winton correction process.png



Check.jpg UPDATED: Japanese Translation for User Interface

The Japanese translation of the UI was updated from version 2.6.

The new Cut Plane control (with the Diameter Cut Plane features) and the new Shortcut Key window is now translated into Japanese.

Vtl-2.8 japanese diameter cut plane.png



Other Pages