|
|
| Line 50: |
Line 50: |
| | | | |
| | | | |
| − | ===[[image:Check.jpg|25px]] Other Changes===
| |
| − | <table cellpadding=10>
| |
| | | | |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | A new tolerance is added for surface point diameter check.
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − |
| |
| − | <table cellpadding=10>
| |
| − |
| |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | The current arm firmware is now read and used by VTube to determine how to handle the arm during Scanner Control changes.
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | [[image:ArmFirmware.jpg|300px]]
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − | <table cellpadding=10>
| |
| − |
| |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | For high-precision end scans, new end-scan techniques are recommended in the VTube-LASER manual.<br><br>
| |
| − | * See [[End-Scan Using the Scissor Motion]]
| |
| − | * See [[End-Scan Using the End Wall]]
| |
| − | * See [[End-Scan Using End Targets]]
| |
| − |
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | [[image:EndScanAfterTarget.jpg|300px]]
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | The VTube SVNET protocol now knows how to handle leftover communications files if they are present.
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | VTube can now save Supravision data to multiple file extension types: $$$, SV, or S2B
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | VTube-LASER now takes in scanned points faster than before.</td>
| |
| − | <td width=300>
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | VTube-LASER installation now allows for installing either MM or INCH default setups.</td>
| |
| − | <td width=300>
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | Default setups were fine-tuned in VTube-LASER so that VTube works faster.</td>
| |
| − | <td width=300>
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| | | | |
| | =Other Pages= | | =Other Pages= |
| | *Back to [[VTube-LASER]] | | *Back to [[VTube-LASER]] |
ENHANCEMENT: Added Page Numbers to Reports in Print Preview
