|
|
| (4 intermediate revisions by one user not shown) |
| Line 40: |
Line 40: |
| | </table> | | </table> |
| | | | |
| − | | + | ===[[image:Check.jpg|25px]] ENHANCED: Removed the Default Radius Setup Message=== |
| − | | + | |
| − | | + | |
| − | | + | |
| − | | + | |
| − | | + | |
| − | ===[[image:Check.jpg|25px]] NEW: "Pull Arm From Resting Position" Message=== | + | |
| | | | |
| | <table cellpadding=10> | | <table cellpadding=10> |
| | <tr valign=top> | | <tr valign=top> |
| | <td width=300> | | <td width=300> |
| − | If the arm uses firmware version 702 or less, then it will display special messages when it is about to update the Scanner Control.<br><br>
| + | The message that says that VTube will automatically set the default radius to 1.5 times the diameter no longer displays as it serves no useful purpose.</td> |
| − | | + | |
| − | Follow these instructions if you change the Scanner Control setup from project to project.<br><br>
| + | |
| − | | + | |
| − | The reason for this new step is that the Scanner Control will not update any integer values to or from VTube-LASER if the LASER is not able to be switched on during setup.
| + | |
| − | </td> | + | |
| | <td width=300> | | <td width=300> |
| − | [[image:RemoveArmFromCradle1.jpg|300px]]
| |
| | </td> | | </td> |
| | </tr> | | </tr> |
| − | </table>
| |
| − |
| |
| − | ===[[image:Check.jpg|25px]] NEW: Separate Cylinder Fit Tolerances for LONG and SHORT Cylinders===
| |
| − |
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | VTube now has a second set of tolerances for shorter straights. This allows for looser tolerances on shorter straights without producing an error message.
| |
| − | <br><br>
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | [[image:LongAndShortCylinderFitSetup.jpg|300px]]
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − |
| |
| − |
| |
| − |
| |
| − | ===[[image:Check.jpg|25px]] Other Changes===
| |
| − | <table cellpadding=10>
| |
| − |
| |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | A new tolerance is added for surface point diameter check.
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − |
| |
| − | <table cellpadding=10>
| |
| − |
| |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | The current arm firmware is now read and used by VTube to determine how to handle the arm during Scanner Control changes.
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | [[image:ArmFirmware.jpg|300px]]
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − | <table cellpadding=10>
| |
| − |
| |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | For high-precision end scans, new end-scan techniques are recommended in the VTube-LASER manual.<br><br>
| |
| − | * See [[End-Scan Using the Scissor Motion]]
| |
| − | * See [[End-Scan Using the End Wall]]
| |
| − | * See [[End-Scan Using End Targets]]
| |
| − |
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | [[image:EndScanAfterTarget.jpg|300px]]
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | The VTube SVNET protocol now knows how to handle leftover communications files if they are present.
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | VTube can now save Supravision data to multiple file extension types: $$$, SV, or S2B
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | VTube-LASER now takes in scanned points faster than before.</td>
| |
| − | <td width=300>
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | VTube-LASER installation now allows for installing either MM or INCH default setups.</td>
| |
| − | <td width=300>
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − | <table cellpadding=10>
| |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | Default setups were fine-tuned in VTube-LASER so that VTube works faster.</td>
| |
| − | <td width=300>
| |
| − | </td>
| |
| − | </tr>
| |
| | </table> | | </table> |
| | | | |
| | =Other Pages= | | =Other Pages= |
| | *Back to [[VTube-LASER]] | | *Back to [[VTube-LASER]] |
ENHANCEMENT: Added Page Numbers to Reports in Print Preview
