|
|
| Line 1: |
Line 1: |
| | [[image:VTube-LASER_OMCGSplash.png|800px]]<br><br> | | [[image:VTube-LASER_OMCGSplash.png|800px]]<br><br> |
| | + | [[image:Numalliance Splash.png|500px]]<br><br> |
| | | | |
| | <table width=1000> | | <table width=1000> |
| Line 16: |
Line 17: |
| | __TOC__ | | __TOC__ |
| | | | |
| − | =OMCG SVNet Communications Protocol in VTube-LASER= | + | ==NUMALLIANCE CORRECTIONS== |
| − | <table width=1000> | + | |
| | + | <table cellpadding=10 width=800> |
| | <tr valign=top> | | <tr valign=top> |
| − | <td width=300>
| |
| − | OMCG added the Supravision Network protocol to their Easy Programming 4 version 2.02 bender control software at the beginning of 2019.<br><br>
| |
| − | As of version 2.9.18, we've embedded the OMCG SVNET protocol in VTube-STEP and VTube-LASER.<br><br>
| |
| − | You can set this protocol in the Benderlink setup grid in System Options.<br><br>
| |
| − | [[image:OMCGSplash.png|300px]]<br><br>
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | [[image:VTube-LASER_OMCGSVNET_BenderSetupScreen.png|700px]]
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| | | | |
| − | <br><br>
| |
| − |
| |
| − | =Using the OMCG Easy Programming 4 Measuring System Interface=
| |
| − | <table width=1000>
| |
| − | <tr valign=top>
| |
| | <td width=300> | | <td width=300> |
| − | Click on the Measuring System button in the toolbar to load the Measure System Interface.<br><br>
| + | VTube-LASER now has an export option for NUMALLIANCE CSV files that is used to '''correct''' the NUMALLIANCE benders.<br><br> |
| − | The window allows you to handle both CORRECTIONS and NOMINAL data.
| + | Note: NUMALLIANCE benders only require the ''measured'' data for corrections.<br><br> |
| | + | Measure the tube in VTube-LASER, then send the MEASURED tube data to the bender control, and it will then perform the correction. |
| | | | |
| − | ===NOMINAL EXPORT===
| + | </td> |
| − | * The NOMINAL EXPORT section allows you to SEND NOMINAL data FROM the OMCG software to VTube-LASER.<br><br>
| + | |
| − | * The NOMINAL EXPORT Enable allows OMCG to automatically respond to a request for NOMINAL data from VTube-LASER.<br><br>
| + | |
| | | | |
| − | ===NOMINAL IMPORT===
| + | <td> |
| − | * The NOMINAL IMPORT section allows you to IMPORT VTube-LASER data INTO the OMCG.<br><br>
| + | [[image:Numalliance Splash.png|500px]]<br><br> |
| − | * In this case, you can load any Supravision file created by VTube-STEP or VTube-LASER into the OMCG control.<br><br>
| + | [[image:VTube-LASER Correcting a NUMALLIANCE Bender.png|500px]] |
| − | | + | |
| − | ===CORRECTIONS===
| + | |
| − | * You can set a variety of options to control how you want the data to come into the OMCG control.<br><br>
| + | |
| − | * Recommended settings:<br><br>
| + | |
| − | | + | |
| − | # Enable corrections<br><br>
| + | |
| − | # Set Apply Mode to "Ask" in order to confirm that you will allow the corrections to be applied.<br><br>
| + | |
| − | # Apply the corrections to any of the three options. (Use the checkboxes.)<br><br>
| + | |
| − | | + | |
| − | | + | |
| − | </td> | + | |
| − | <td width=300>
| + | |
| − | [[image:OMCGScreen_WithMeasuringSystem.png|700px]]<br><br> | + | |
| − | ----------------
| + | |
| − | [[image:OMCGScreen_MeasuringSystemInterface_Window.png|700px]] | + | |
| | </td> | | </td> |
| | </tr> | | </tr> |
| | + | |
| | </table> | | </table> |
| − |
| |
| | <br><br> | | <br><br> |
| | | | |
| − | =Configuring the OMCG Measuring System Interface=
| |
| − | <table width=1000>
| |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | Click on the setup button in the Measuring System Interface menu to configure the measuring center communications.<br><br>
| |
| − |
| |
| − | ===Configuring the Settings===
| |
| − | * Bender Name: This is mnemonic. It is to help you know which bender is associated with the bender number.<br><br>
| |
| − | * Bender Number: The Supravision network protocol requires that every bend have a unique number if the benders are sharing the same network path for communications.<br><br>
| |
| − | * Paths: These are the paths used for VTube-LASER to communicate with the OMCG software.<br><br>
| |
| − | * Timeouts: These are timeouts that allow the OMCG to know when it has waited too long for data to move in either direction.<br><br>
| |
| − | * Radius Adjust Enable: This allows VTube-LASER to change the radius values with nominal and corrections communications.<br><br>
| |
| − | * Allow negative angle: Wire benders can bend left or right depending on the sign of the bend angle. It is normal to make this feature active.<br><br>
| |
| − |
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | [[image:OMCGScreen_MeasuringSystemInterface_Configuration_Window.png|700px]]
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| − |
| |
| − |
| |
| − | =OMCG Documentation from OMCG=
| |
| − | <table width=1000>
| |
| − | <tr valign=top>
| |
| − | <td width=300>
| |
| − | This is the official OMCG Document (PDF - English) for setup and use of the OMCG SVNET protocol.<br><br>
| |
| − |
| |
| − | Download the [https://www.advancedtubular.com/vtube-laser/20190222%20OMCG%20EP4%20Measuring%20System%20%20ENG%20v1.3.pdf OMCG PDF Setup Document]
| |
| − |
| |
| − | </td>
| |
| − | <td width=300>
| |
| − | [[image:OMCGScreen_SetupDocument_PDFScreenShot.png|400px]]
| |
| − | </td>
| |
| − | </tr>
| |
| − | </table>
| |
| | | | |
| | ==Other Pages== | | ==Other Pages== |
| | * See [[VTube-LASER]] | | * See [[VTube-LASER]] |
| | * See [[VTube-STEP]] | | * See [[VTube-STEP]] |
