Difference between revisions of "Output Sustain in Seconds"

From ATTWiki
Jump to: navigation, search
(Changing the Value)
 
(10 intermediate revisions by one user not shown)
Line 1: Line 1:
[[Image:Cnclite lowlevel processor.jpg|thumb|Test]]
+
[[Image:Cnclite lowlevel processor.jpg|thumb|CNC Bender Lite - PROCESSOR Tab of Low Level Menu]]
  
  
 
This is a LOW LEVEL variable in CNC Bender that allows you to set the sustain time for the output module that keeps the bender running.<p>
 
This is a LOW LEVEL variable in CNC Bender that allows you to set the sustain time for the output module that keeps the bender running.<p>
The default value is 10 seconds.  But in some cases, it may be necessary to set this value higher if other processes require too much CPU time to service this output module within 10 seconds.  This may be the situation when building a very large process list in CNC Bender Lite software while the bender is running.
 
  
 
</p>
 
</p>
Line 10: Line 9:
  
  
===Advanced Optimization Ideas===
+
===Why Change This Value?===
  
 
<table cellpadding="15" width = 650>
 
<table cellpadding="15" width = 650>
 
<tr valign="top">
 
<tr valign="top">
 
<td bgcolor="#f0f0f0" width = 200>
 
<td bgcolor="#f0f0f0" width = 200>
Be sure all axes are tuned properly.
+
Master power shuts off during Process List build.
 
</td>
 
</td>
 
<td bgcolor="#e3e4f5">
 
<td bgcolor="#e3e4f5">
 
<ol>  
 
<ol>  
<li>Use I2T HMI software for setting PID values so that motion is smooth and yet precise.</li><br>
+
The default value is 10 seconds.  But in some cases, it may be necessary to set this value higher if other processes require too much CPU time to service this output module within 10 seconds.  This may be the situation when building a very large process list in CNC Bender Lite software while the bender is running.
image:Cnclite lowlevel processor.jpg
+
 
 
</ol>
 
</ol>
 
</td>
 
</td>
Line 30: Line 29:
 
<tr valign="top">
 
<tr valign="top">
 
<td bgcolor="#f0f0f0" width = 200>
 
<td bgcolor="#f0f0f0" width = 200>
Be sure all axes and actuators are travelling at maximum sustainable speed.
+
Master power pops off/on from time to time.
 
</td>
 
</td>
 
<td bgcolor="#e3e4f5">
 
<td bgcolor="#e3e4f5">
 
<ol>  
 
<ol>  
<li>This requires monitoring the output voltages of the axis controllers(Use the I2T HMI software to monitor output voltages.)</li><br>
+
The output module sustain time is either too low, or some other process in the operator station is taking too much of the CPU timeIt is possible that the name of the output module in this menu is incorrect. If this is the case then the default sustain time of 1 second is used.  (One second is too  low for most bender systems.)
<li>When running at speed 10, is the voltage at 80-90% of the maximum?</li>
+
 
</ol>
 
</ol>
 
</td>
 
</td>
Line 42: Line 40:
  
  
See also [[Bend Program Optimization]]
+
===Changing the Value===
 +
 
 +
Change the value by touching the field in the Special Communications Parameters section.  Set the value in whole seconds.
 +
 
 +
[[Image:cnclite_lowlevel_processor_output10seconds.jpg|CNC Bender Lite - PROCESSOR Tab, Special Communications section of Low Level Menu]]
 +
 
 +
 
 +
In this example, the value has been changed to 30 seconds.
 +
 
 +
[[Image:cnclite_lowlevel_processor_output30seconds_circled.jpg|CNC Bender Lite - PROCESSOR Tab, Special Communications section of Low Level Menu]]
 +
 
 +
 
 +
 
 +
See also [[Master Power On]]<br>
  
--[[User:Mcone|Mcone]] 10:32, 20 July 2006 (EDT)
+
--[[User:Mcone|Mcone]] 15:03, 11 January 2007 (EST)

Latest revision as of 20:19, 11 January 2007

CNC Bender Lite - PROCESSOR Tab of Low Level Menu


This is a LOW LEVEL variable in CNC Bender that allows you to set the sustain time for the output module that keeps the bender running.



Why Change This Value?

Master power shuts off during Process List build.

    The default value is 10 seconds. But in some cases, it may be necessary to set this value higher if other processes require too much CPU time to service this output module within 10 seconds. This may be the situation when building a very large process list in CNC Bender Lite software while the bender is running.


Master power pops off/on from time to time.

    The output module sustain time is either too low, or some other process in the operator station is taking too much of the CPU time. It is possible that the name of the output module in this menu is incorrect. If this is the case then the default sustain time of 1 second is used. (One second is too low for most bender systems.)


Changing the Value

Change the value by touching the field in the Special Communications Parameters section. Set the value in whole seconds.

CNC Bender Lite - PROCESSOR Tab, Special Communications section of Low Level Menu


In this example, the value has been changed to 30 seconds.

CNC Bender Lite - PROCESSOR Tab, Special Communications section of Low Level Menu


See also Master Power On

--Mcone 15:03, 11 January 2007 (EST)