VTube Communication for CRIPPA Supravision - Revision history

Mcone: /* STEP 2: Setup the Benderlink Network Grid for CRIPPA Supravision Network Protocol */

2018-01-12T03:10:41Z

‎STEP 2: Setup the Benderlink Network Grid for CRIPPA Supravision Network Protocol

Mcone: /* STEP 2: Setup the Benderlink Network Grid for CRIPPA Supravision Network Protocol */

2018-01-12T03:10:03Z

‎STEP 2: Setup the Benderlink Network Grid for CRIPPA Supravision Network Protocol

Mcone: /* STEP 2: Setup the Benderlink Network Grid for CRIPPA Supravision Network Protocol */

2018-01-12T03:09:44Z

‎STEP 2: Setup the Benderlink Network Grid for CRIPPA Supravision Network Protocol

Mcone: /* STEP 2: Setup the Benderlink Network Grid for CRIPPA Supravision Network Protocol */

2018-01-12T03:09:25Z

‎STEP 2: Setup the Benderlink Network Grid for CRIPPA Supravision Network Protocol

Mcone: /* STEP 10 - Go Back to STEP 1 - Bend the Tube */

2017-08-12T02:24:45Z

‎STEP 10 - Go Back to STEP 1 - Bend the Tube

Mcone: /* STEP 9 - SAVE the New Data at the CRIPPA UII Software */

2017-08-12T02:23:15Z

‎STEP 9 - SAVE the New Data at the CRIPPA UII Software

Mcone: /* STEP 9 - SAVE the New Data at the CRIPPA UII Software */

2017-08-12T02:22:38Z

‎STEP 9 - SAVE the New Data at the CRIPPA UII Software

Mcone: /* STEP 9 - SAVE the New Data at the CRIPPA UII Software */

2017-08-12T02:22:01Z

‎STEP 9 - SAVE the New Data at the CRIPPA UII Software

Mcone: /* STEP 9 - SAVE the New Data at the CRIPPA UII Software */

2017-08-12T02:21:43Z

‎STEP 9 - SAVE the New Data at the CRIPPA UII Software

Mcone: /* STEP 7 - Send the CORRECTION Values to the CRIPPA */

2017-08-12T02:21:28Z

‎STEP 7 - Send the CORRECTION Values to the CRIPPA

@@ Line 157: / Line 157: @@
 #Enter the IP address in the PING IP ADDRESS field if it is a fixed field. (This is not required. It allows VTube to ping the address to see if the network location is active before trying to open communications.)<br><br>
 #If the Crippa rotates the Clockwise positive, then select YES in the CW Rotation Positive cell.<br><br>
-#The "Ignore Incoming Linear Unit" setting is optional.  This will not allow the CRIPPA to change the linear units in VTube-LASER if they are different.<br><br>'''SOME CRIPPA BENDERS ALWAYS SEND DATA IN MILLIMETERS - EVEN IF THE LINEAR UNIT SETTING IN THE FILE IS SET TO INCHES. THIS SETTING MUST BE ENABLED TO OVERCOME THAT ISSUE. ALSO, THEN RECALL ALWAYS WITH VTUBE-LASER SET TO MILLIMETERS.'''<br><br>
+#The "Ignore Incoming Linear Unit" setting is optional.  This will not allow the CRIPPA to change the linear units in VTube-LASER if they are different.<br><br>'''SOME CRIPPA BENDERS ALWAYS SEND DATA IN MILLIMETERS - EVEN IF THE LINEAR UNIT SETTING IN THE FILE IS SET TO INCHES. THIS SETTING MUST BE ENABLED TO OVERCOME THAT ISSUE. IF THIS IS THE CASE, THEN IT ALSO IMPORTANT TO RECALL WITH VTUBE-LASER SET TO MILLIMETERS.'''<br><br>
 #Press Close to save the settings.  VTube will save these values to a persistent configuration file that will not change unless you change them in this grid.

@@ Line 157: / Line 157: @@
 #Enter the IP address in the PING IP ADDRESS field if it is a fixed field. (This is not required. It allows VTube to ping the address to see if the network location is active before trying to open communications.)<br><br>
 #If the Crippa rotates the Clockwise positive, then select YES in the CW Rotation Positive cell.<br><br>
-#The "Ignore Incoming Linear Unit" setting is optional.  This will not allow the CRIPPA to change the linear units in VTube-LASER if they are different.<br><br>'''SOME CRIPPA BENDERS ALWAYS SEND DATA IN MILLIMETERS - EVEN IF THE LINEAR UNIT SETTING IN THE FILE IS SET TO INCHES. THIS SETTING MUST BE ENABLED TO OVERCOME THAT ISSUE.
+#The "Ignore Incoming Linear Unit" setting is optional.  This will not allow the CRIPPA to change the linear units in VTube-LASER if they are different.<br><br>'''SOME CRIPPA BENDERS ALWAYS SEND DATA IN MILLIMETERS - EVEN IF THE LINEAR UNIT SETTING IN THE FILE IS SET TO INCHES. THIS SETTING MUST BE ENABLED TO OVERCOME THAT ISSUE. ALSO, THEN RECALL ALWAYS WITH VTUBE-LASER SET TO MILLIMETERS.'''<br><br>
- ALSO, THEN RECALL ALWAYS WITH VTUBE-LASER SET TO MILLIMETERS.'''<br><br>
 #Press Close to save the settings.  VTube will save these values to a persistent configuration file that will not change unless you change them in this grid.

@@ Line 157: / Line 157: @@
 #Enter the IP address in the PING IP ADDRESS field if it is a fixed field. (This is not required. It allows VTube to ping the address to see if the network location is active before trying to open communications.)<br><br>
 #If the Crippa rotates the Clockwise positive, then select YES in the CW Rotation Positive cell.<br><br>
-#The "Ignore Incoming Linear Unit" setting is optional.  This will not allow the CRIPPA to change the linear units in VTube-LASER if they are different. '''SOME CRIPPA BENDERS ALWAYS SEND DATA IN MILLIMETERS - EVEN IF THE LINEAR UNIT SETTING IN THE FILE IS SET TO INCHES. THIS SETTING MUST BE ENABLED TO OVERCOME THAT ISSUE.
+#The "Ignore Incoming Linear Unit" setting is optional.  This will not allow the CRIPPA to change the linear units in VTube-LASER if they are different.<br><br>'''SOME CRIPPA BENDERS ALWAYS SEND DATA IN MILLIMETERS - EVEN IF THE LINEAR UNIT SETTING IN THE FILE IS SET TO INCHES. THIS SETTING MUST BE ENABLED TO OVERCOME THAT ISSUE.
   ALSO, THEN RECALL ALWAYS WITH VTUBE-LASER SET TO MILLIMETERS.'''<br><br>
 #Press Close to save the settings.  VTube will save these values to a persistent configuration file that will not change unless you change them in this grid.

@@ Line 157: / Line 157: @@
 #Enter the IP address in the PING IP ADDRESS field if it is a fixed field. (This is not required. It allows VTube to ping the address to see if the network location is active before trying to open communications.)<br><br>
 #If the Crippa rotates the Clockwise positive, then select YES in the CW Rotation Positive cell.<br><br>
-#The "Ignore Incoming Linear Unit" setting is optional.  This will not allow the CRIPPA to change the linear units in VTube-LASER if they are different.<br><br>
+#The "Ignore Incoming Linear Unit" setting is optional.  This will not allow the CRIPPA to change the linear units in VTube-LASER if they are different. '''SOME CRIPPA BENDERS ALWAYS SEND DATA IN MILLIMETERS - EVEN IF THE LINEAR UNIT SETTING IN THE FILE IS SET TO INCHES. THIS SETTING MUST BE ENABLED TO OVERCOME THAT ISSUE.
 #Press Close to save the settings.  VTube will save these values to a persistent configuration file that will not change unless you change them in this grid.

@@ Line 438: / Line 438: @@
 </table>
-===STEP 10 - Go Back to STEP 1 - Bend the Tube===
+===STEP 10 - REPEAT STEPS 1 THROUGH 9===
 <table cellpadding=10>
 <tr valign=top>
 <td width=300>
-Bend the tube in the CRIPPA, then measure it again.<br><br>
+Bend the tube in the CRIPPA (Step 1) then measure it again (Step 2) and follow the rest of the steps until the part is within tolerance.
-Repeat these steps until the part is within tolerance.
 <td>
 [[image:CRIPPA User Programming UII.png|400px]]

@@ Line 429: / Line 429: @@
 If you don't see this green banner, then communications did not occur.  You will need to trouble-shoot the connection to make it work.<br><br>
 The YBC data will change to match the data that was sent from VTube. You can compare a few values to be sure the data was updated properly.<br><br>
-The VTube-LASER SEND will only update the UII data on the CRIPPA screen.  (Remember: CRIPPA only returns data from the file - see "RECALL" above.) This data must be SAVED to the disk and compiled to take effect.<br><br>
+The VTube-LASER SEND will only update the UII data on the CRIPPA screen.  (Remember: CRIPPA only returns data from the file - see "RECALL" above.) This new data that the CRIPPA UII screen just received from VTube-LASER must be SAVED to the disk and compiled to take effect.<br><br>
 </td>

@@ Line 426: / Line 426: @@
 <tr valign=top>
 <td width=400>
-Unlike the RECALL, the SEND will only update the UII data on the CRIPPA screen.  (Remember: CRIPPA only returns data from the file - see "RECALL" above.) This data must be SAVED to the disk and compiled to take effect.<br><br>
+The SEND will only update the UII data on the CRIPPA screen.  (Remember: CRIPPA only returns data from the file - see "RECALL" above.) This data must be SAVED to the disk and compiled to take effect.<br><br>
 Move to the CRIPPA control. CRIPPA will ask for confirmation to update when it receives the incoming data.  Say "Yes".<br><br>
 If you don't see this green banner, then communications did not occur.  You will need to trouble-shoot the connection to make it work.<br><br>

@@ Line 403: / Line 403: @@
 Click on AUTO SEND. This will send the ORANGE columns to the CRIPPA bender.<br><br>
 To be sure that a RECALL has recently been performed, VTube will show a CRIPPA CORRECTIONS NOTES as a reminder.<br><br>
-Unlike the RECALL, the SEND will only update the UII data on the CRIPPA screen.  (Remember: CRIPPA only returns data from the file - see "RECALL" above.) This data must be SAVED to the disk and compiled to take effect.
 <td>