VTube-STEP v2 - Revision history

Mcone: /* 25px ENHANCED: SUPRAVISION Network Engine Now Handles Benders with Inverted Rotations */

2015-02-16T23:36:54Z

‎25px ENHANCED: SUPRAVISION Network Engine Now Handles Benders with Inverted Rotations

2015-02-16T23:01:42Z

‎25px ENHANCED: SUPRAVISION NETWORK Engine Now Allows for Inverted Rotations

2015-02-16T22:55:47Z

‎25px Other Changes

2015-02-16T22:55:23Z

‎25px ENHANCED: CSM and ALPINE File Data Transfer Tested and Improved

2015-02-16T22:54:51Z

‎25px ENHANCED: CSM and ALPINE File Data Transfer Tested and Improved

2015-02-16T22:54:26Z

‎25px ENHANCED: CSM and ALPINE File Data Transfer Tested and Improved

2015-02-16T22:51:29Z

‎25px ENHANCED: CSM and ALPINE File Data Transfer Tested and Improved

2015-02-16T22:51:17Z

‎25px Other Changes

2015-02-16T22:51:02Z

‎25px ENHANCED: CSM and ALPINE File Data Conversions Improved

2015-02-16T22:50:03Z

‎25px FIXED: Ball Probe - Missing Incoming Point Data

@@ Line 39: / Line 39: @@
-===[[image:Check.jpg|25px]] ENHANCED: SUPRAVISION Network Engine Now Handles Benders with Inverted Rotations===
+===[[image:Check.jpg|25px]] NEW: SUPRAVISION Network Engine Now Handles Benders with Inverted Rotations===
 <table cellpadding=10>
 <tr valign=top>

@@ Line 39: / Line 39: @@
-===[[image:Check.jpg|25px]] ENHANCED: SUPRAVISION NETWORK Engine Now Allows for Inverted Rotations===
+===[[image:Check.jpg|25px]] ENHANCED: SUPRAVISION Network Engine Now Handles Benders with Inverted Rotations===
 <table cellpadding=10>
 <tr valign=top>

@@ Line 66: / Line 66: @@
 ===[[image:Check.jpg|25px]] Other Changes===
-* The VTube configuration file location was changed to the more standard "c:\ProgramData\VTube" location.<br><br>
+* The VTube configuration file location was changed to the more standard '''"c:\ProgramData\VTube"''' location.<br><br>
 * The installation performs a better job of setting up the configuration file location.<br><br>
 * The Supravision network engine has been enhanced to handle data files that don't follow the Supravison spec perfectly.<br><br>

@@ Line 54: / Line 54: @@
 <tr valign=top>
 <td width=400>
-* The [[CSM]] and [[Alpine]] conversions now correctly invert the rotation value in both M3 and M4 controls - since they move in the opposite direction from VTube rotations.<br><br>
+* The CSM and Alpine conversions now correctly invert the rotation value in both M3 and M4 controls - since they move in the opposite direction from VTube rotations.<br><br>
 * Other adjustments and fixes to the conversion were tested with both styles of bender controls.<br><br>
 * When VTube sends corrections to the M4 controls, it now changes the adjustment values rather than the nominal values in the YBC page.

@@ Line 54: / Line 54: @@
 <tr valign=top>
 <td width=400>
-* The CSM and Alpine conversions now correctly invert the rotation value in both M3 and M4 controls - since they move in the opposite direction from VTube rotations.<br><br>
+* The [[CSM]] and [[Alpine]] conversions now correctly invert the rotation value in both M3 and M4 controls - since they move in the opposite direction from VTube rotations.<br><br>
 * Other adjustments and fixes to the conversion were tested with both styles of bender controls.<br><br>
 * When VTube sends corrections to the M4 controls, it now changes the adjustment values rather than the nominal values in the YBC page.

@@ Line 62: / Line 62: @@
 </tr>
 </table>
 ===[[image:Check.jpg|25px]] Other Changes===

@@ Line 67: / Line 67: @@
 * The installation performs a better job of setting up the configuration file location.<br><br>
 * The Supravision network engine has been enhanced to handle data files that don't follow the Supravison spec perfectly.<br><br>
-* We fixed a ball probe measurement issue where VTube would sometimes not always take in single points from the FARO driver.  This issue created problems with measuring cut planes too.  If you measured cut planes, and still couldn't get the cut plane to work properly, then it was probably due to this issue.<br>
+* We fixed a ball probe measurement issue where VTube would sometimes not always take in single points from the FARO driver.  This issue created problems with measuring cut planes too.  If you measured cut planes, and still couldn't get the cut plane to work properly, then it was probably due to this issue.<br><br><br>
 ==Other==

@@ Line 46: / Line 46: @@
 <td width=400>
 [[image:vtube-2_cwrotation_svnetwork.png|400px]]
 </td>
 </tr>