VTube-STEP v1.94 - Revision history

Mcone: /* 25px FIX: Alpine M4 Export */

2014-09-01T14:26:56Z

‎25px FIX: Alpine M4 Export

2014-09-01T14:14:23Z

‎25px CRITICAL ENHANCEMENT: Cylinder Centerline Calculation in Math Engine Improved Significantly

2014-09-01T14:11:34Z

‎25px NEW: Multiple Trim Surface Datums for Trimming or Extending End Lengths

2014-09-01T14:11:02Z

‎25px CRITICAL ENHANCEMENT: Cylinder Centerline Calculation in Math Engine Improved Significantly

2014-09-01T14:10:31Z

‎25px CRITICAL ENHANCEMENT: Cylinder Centerline Calculation in Math Engine Improved Significantly

2014-09-01T02:30:57Z

‎25px NEW: Add A Second Language Column To Language Editor

2014-09-01T02:28:10Z

‎25px NEW: Add A Second Language Column To Language Editor

2014-09-01T02:27:49Z

‎25px NEW: Add A Second Language Column To Language Editor

2014-09-01T02:27:10Z

‎25px FIX: Alpine M4 Export

2014-09-01T01:12:46Z

‎25px Other Changes

@@ Line 144: / Line 144: @@
 </tr>
 </table>
 ===[[image:Check.jpg|25px]] NEW: Add A Second Language Column To Language Editor ===

@@ Line 26: / Line 26: @@
 <td width=300>
 '''THE STARTING CENTERLINE CALCULATION PROJECTION TOLERANCE IS NOW REDUCED to a 10th of a MICRON'''<br><br>
-To enhance the calculations, the automatic Projection Tolerance in VTube-STEP now starts with an much smaller projection tolerance at 1/10th of a micron (0.0001 mm, or 0.000003937 inches).<br><br>
+To enhance the calculations, the automatic Projection Tolerance in VTube-STEP now starts with a much smaller projection tolerance at 1/10th of a micron (0.0001 mm, or 0.000003937 inches).<br><br>
 If the centerline for the cylinders cannot be solved for, then VTube increases the projection tolerance until it finds a solution.<br><br>
 The final projection tolerance used is stored in the Collection grid so that you can view the result at any time after a calculation.

@@ Line 50: / Line 50: @@
 <tr valign=top>
 <td width=300>
-Older versions only allow for the centroid (average XYZ point) of all points in a solid used to trim.  This version allows for FURTHEST or NEAREST in the cloud of surface points.
+Earlier versions only allow for the centroid (average XYZ point) of all points in a solid used to trim.  This version allows for FURTHEST or NEAREST in the cloud of surface points.
 </td>
 <td width=500>

@@ Line 38: / Line 38: @@
 <td width=300>
 '''THE CENTERLINE CALCULATION for ROUGH CYLINDERS IS SIGNIFICANTLY ENHANCED'''<br><br>
-Sometimes VTube is asked to calculate the centerline of a cylinder that's not really a cylinder.  VTube can handle approximate cylinders much better in this version than in previous versions.<br><br>  This includes projections for cylinders with forms like coping and bulges or holes - or just inaccurate surfaces.</td>
+Sometimes VTube is asked to calculate the centerline of a cylinder that's not a true cylinder.  VTube can handle approximate cylinders much better in this version than in previous versions.<br><br>  This includes projections for cylinders with forms like coping and bulges or holes - or just inaccurate surfaces.</td>
 <td width=500>
 [[image:vtube-step-1.94_coping_handled.png|400px]]

@@ Line 26: / Line 26: @@
 <td width=300>
 '''THE STARTING CENTERLINE CALCULATION PROJECTION TOLERANCE IS NOW REDUCED to a 10th of a MICRON'''<br><br>
-To enhance the calculations, the automatic Projection Tolerance in VTube-STEP now starts with an much smaller projection tolerance at a 10th of a micron (0.0001 mm, or 0.000003937 inches).<br><br>
+To enhance the calculations, the automatic Projection Tolerance in VTube-STEP now starts with an much smaller projection tolerance at 1/10th of a micron (0.0001 mm, or 0.000003937 inches).<br><br>
 If the centerline for the cylinders cannot be solved for, then VTube increases the projection tolerance until it finds a solution.<br><br>
 The final projection tolerance used is stored in the Collection grid so that you can view the result at any time after a calculation.

@@ Line 150: / Line 150: @@
 <tr valign=top>
 <td width=300>
-Our translators asked for this feature so that they could always see English next to the translated language.  So it allows you to bring in a second language column to compare to the first column.  The values in each cell are matched by component names to ensure an appropriate match.<br><br>
+Our translators asked for this feature so that they could always see English next to the translated language.<br><br>
 To use this feature, load any language setup into VTube, then enter the language editor, press the new Add Matching Setup button, then choose a second language to bring into the editor.
 </td>

@@ Line 154: / Line 154: @@
 </td>
 <td width=400>
-[[image:vtube-1.94_add_separate_language_column_to_language_editor.png|400px]]
+[[image:vtube-1.94_add_separate_language_column_to_language_editor.png|600px]]
 </td>
 </tr>

@@ Line 141: / Line 141: @@
 <td width=400>
 [[image:alpinebender_userscreen_radiuslevel0_fix.png|400px]]
 </td>
 </tr>

@@ Line 152: / Line 152: @@
 * Fixed a bug in the Recent Folder data in the Quick Load Dialog for project files and import files.
 <br>
 </td>