VTube-STEP and VTube-LASER Project File Compatibility - Revision history

Mcone: /* All VTube License Modes Have 100% Compatible Project Files */

2016-02-25T16:49:13Z

‎All VTube License Modes Have 100% Compatible Project Files

2016-02-25T16:48:08Z

‎All VTube License Modes Have 100% Compatible Project Files

2016-02-25T16:47:53Z

‎All VTube License Modes Have 100% Compatible Project Files

2016-02-25T16:47:00Z

‎All VTube License Modes Have 100% Compatible Project Files

2016-02-24T21:03:30Z

‎How To Save Project Files that Compatible Even with Older Versions

2016-02-24T21:03:00Z

‎How To Save Project Files that Compatible Even with Older Versions

2016-02-24T21:02:47Z

‎How To Save Project Files that Compatible Even with Older Versions

2016-02-24T21:01:08Z

‎How To Save Project Files that Compatible Even with Older Versions

2016-02-24T21:00:34Z

‎About the VTube-LASER Programmer License

2016-02-24T20:59:59Z

‎About the VTube-LASER Programmer License

@@ Line 26: / Line 26: @@
 For example, anyone who runs VTube-STEP can setup and save a VTube Project file (.vtp) that can be loaded into VTube-LASER or VTube-LASER Programmer.<br><br>
-For customers that want to enter VTube-LASER data in remote locations (that is, away from the FARO arm), they will purchase and use VTube-STEP or VTube-LASER Programmer at reduced cost to create the setup for VTube then save the new VTP project file to a shared network location.<br><br>
+This is ideal for customers that want to enter VTube-LASER data in remote locations (that is, away from the FARO arm).  They purchase and use a separate license of VTube-STEP or VTube-LASER Programmer at reduced cost to create the setup for VTube then save the new VTP project file to a shared network location.<br><br>
 Then, when FARO operators need to measure and qualify that same part, they load the VTP project file from the network location into VTube-LASER, then send data to the bender, and/or start measuring the tube that was already bent.

@@ Line 26: / Line 26: @@
 For example, anyone who runs VTube-STEP can setup and save a VTube Project file (.vtp) that can be loaded into VTube-LASER or VTube-LASER Programmer.<br><br>
-For customers that want to enter VTube-LASER data in remote locations (that is, away from the FARO arm), they will purchase and use VTube-STEP or VTube-LASER Programmer at reduced cost to create the setup for VTube then save the new VTP file to a shared network location.<br><br>
+For customers that want to enter VTube-LASER data in remote locations (that is, away from the FARO arm), they will purchase and use VTube-STEP or VTube-LASER Programmer at reduced cost to create the setup for VTube then save the new VTP project file to a shared network location.<br><br>
 Then, when FARO operators need to measure and qualify that same part, they load the VTP project file from the network location into VTube-LASER, then send data to the bender, and/or start measuring the tube that was already bent.

@@ Line 26: / Line 26: @@
 For example, anyone who runs VTube-STEP can setup and save a VTube Project file (.vtp) that can be loaded into VTube-LASER or VTube-LASER Programmer.<br><br>
-For customers that want to enter VTube-LASER data in remote locations (that is, away from the FARO arm), they will purchase and use VTube-STEP or VTube-LASER Programmer at reduced cost to setup VTube then save the new VTP file to a shared network location.<br><br>
+For customers that want to enter VTube-LASER data in remote locations (that is, away from the FARO arm), they will purchase and use VTube-STEP or VTube-LASER Programmer at reduced cost to create the setup for VTube then save the new VTP file to a shared network location.<br><br>
 Then, when FARO operators need to measure and qualify that same part, they load the VTP project file from the network location into VTube-LASER, then send data to the bender, and/or start measuring the tube that was already bent.

@@ Line 25: / Line 25: @@
 VTube-STEP, VTube-LASER Programmer, and VTube-LASER save project files that are 100% compatible with each other.<br><br>
 For example, anyone who runs VTube-STEP can setup and save a VTube Project file (.vtp) that can be loaded into VTube-LASER or VTube-LASER Programmer.<br><br>
-Customers use this capability to save license cost by purchasing VTube-STEP or VTube-LASER Programmer when entering setup data in remote locations that are not near their FARO arm with VTube-LASER.  When a FARO operator needs to measure the part as defined in the VTP file, then he or she loads the part from the network location into VTube-LASER.
 </td>
 <td>

@@ Line 65: / Line 65: @@
 <td>
 [[image:vtube_saveas_dialog_project_fileversion.png|500px]]<br><br>
-[[image:vtube_saveas_dialog_project_fileversion_example.png|530px]]
+[[image:vtube_saveas_dialog_project_fileversion_example.png|520px]]
 </td>
 </tr>

@@ Line 59: / Line 59: @@
 <tr valign=top>
 <td width=300>
-All newer versions of VTube can load the project files from any older versions.<br><br>
+All newer versions of VTube can load the project files from older versions of VTube.<br><br>
 Older versions don't recognize newer files, '''but newer versions can save in older file formats in the Save As Dialog as shown in the images on the right'''.<br><br>
 To determine the version of VTP file your VTube uses, click on the '''Save as Type''' pulldown list, and look for the latest version at the top of the list.  VTube will, by default, always save the latest version of the VTP file.<br><br>

@@ Line 43: / Line 43: @@
 You can setup a VTube-LASER project in VTube-STEP.<br><br>
 However, some customers also want to setup the LASER mode '''MEASURE SETUP variables''' that are not available in STEP mode - and they want to do this in remote locations away from the FARO ScanArm computer.  So they purchase VTube-LASER Programmer to do this.<br><br>
-The VTube-LASER PROGRAMMER version is identical to VTube-LASER except that it cannot connect to a FARO arm to measure parts.<br><br>Programmer mode costs half of a regular VTube-LASER license.
+The VTube-LASER PROGRAMMER version is identical to VTube-LASER except that it will not connect to a FARO arm to measure parts.<br><br>Programmer mode costs half of a regular VTube-LASER license.
 <br><br>
 </td>