VTube-LASER v2.9.2 - Revision history

Mcone: /* 25pxFIXED and IMPROVED - END TRIM */

2017-12-12T23:11:05Z

‎25pxFIXED and IMPROVED - END TRIM

2017-12-12T23:10:35Z

‎Revision 2.9.2 Build 104

2017-12-12T23:10:23Z

‎25pxOther

2017-12-12T23:10:06Z

‎25pxOther

2017-12-12T00:15:18Z

‎25pxFIXED and IMPROVED - END TRIM

2017-12-12T00:14:09Z

‎25pxFIXED and IMPROVED - END TRIM

2017-12-12T00:13:09Z

‎25pxFIXED and IMPROVED - Bend Profile Calculations

2017-12-01T22:00:35Z

‎25pxOther

2017-12-01T21:58:39Z

‎25pxOther

2017-12-01T21:58:26Z

‎25pxOther

← Older revision		Revision as of 23:11, 12 December 2017
Line 62:		Line 62:


−	==[[image:Check.jpg\|25px]]FIXED and IMPROVED - END TRIM==	+	==[[image:Check.jpg\|25px]]FIXED and IMPROVED - END TRIM - (Build 108)==

	<table cellpadding=10 width=800>		<table cellpadding=10 width=800>

@@ Line 5: / Line 5: @@
-==Revision 2.9.2 Build 104==
+==Revision 2.9.2 Build 109==
-Release Date: December 1, 2017<br>
+Release Date: December 12, 2017<br>
 * Back to [[VTube-LASER]]

@@ Line 88: / Line 88: @@
 <td width=500>
 * A bug was discovered for saving the Default Project file where some of values recently changed would not be stored in the default setup. '''This is fixed.'''<br><br>
-* The Bender Data Setup window bender number was always reset to 1 whenever the measured tube was created. This has been fixed so that the previously selected bender is remembered and displayed.
+* (Build 109) - The Bender Data Setup window bender number was always reset to 1 whenever the measured tube was created. This has been fixed so that the previously selected bender is remembered and displayed.
 </td>

@@ Line 87: / Line 87: @@
 <td width=500>
-* A bug was discovered for saving the Default Project file where some of values recently changed would not be stored in the default setup. '''This is fixed.'''
+* A bug was discovered for saving the Default Project file where some of values recently changed would not be stored in the default setup. '''This is fixed.'''<br><br>
 </td>

@@ Line 69: / Line 69: @@
 <td width=300>
 A customer discovered a rare end trim condition that we were able to reproduce and fix.  The issue occurred when end trim stripes were captured both near the end and near the first or last bend. This confused the end trim logic. The logic has been completely redesigned to not only overcome this issue - but to find the end-trim even faster than before.<br><br>
-Our tests also showed that, with this new logic, the end-scan technique is not as important as it was in previous versions. The key is to be sure that the END WALL is the furthest point out in an end scan.
+Our tests also showed that, with this new logic, the end-scan technique is not as important as it was in previous versions. The key is to be sure that the END WALL is the furthest point out in an end scan.<br><br>
 </td>

← Older revision		Revision as of 00:13, 12 December 2017
Line 61:		Line 61:


		+
		+	==[[image:Check.jpg\|25px]]FIXED and IMPROVED - END TRIM==
		+
		+	<table cellpadding=10 width=800>
		+	<tr valign=top>
		+
		+	<td width=300>
		+	A customer discovered a rare end trim condition that we were able to reproduce and fix. The issue occurred when end trim stripes were captured both near the end and near the first or last bend. This confused the end trim logic. The logic has been completely redesigned to not only overcome this issue - but to find the end-trim even faster than before.<br><br>
		+	Our tests also showed that the end-scan technique is not as important as it was in previous versions. The key is to be sure that the END WALL is the furthest point out in an end scan.
		+	</td>
		+
		+	<td>
		+	[[image:vtl_2.9.2_endtrim_from_scans_furthest.png\|500px]]<br><br>
		+	</td>
		+	</tr>
		+
		+	</table>
		+	<br><br>

	==[[image:Check.jpg\|25px]]Other==		==[[image:Check.jpg\|25px]]Other==

@@ Line 67: / Line 67: @@
 <tr valign=top>
-<td width=300>
+<td width=500>
 * You can now change items inside the System Options window and immediately save them as part of the default project setup inside System Option. (In previous versions, it was necessary to exit System Options then re-enter before saving the default project.)
 </td>

@@ Line 72: / Line 72: @@
 <td>
 </td>
 </tr>