VTube-LASER v2.9.10 - Revision history

Mcone: /* 25pxNEW LASER SCAN FILTER - MINIMUM NUMBER OF POINTS REQUIRED IN LASER STRIPES */

2018-07-11T04:44:41Z

‎25pxNEW LASER SCAN FILTER - MINIMUM NUMBER OF POINTS REQUIRED IN LASER STRIPES

2018-07-11T04:42:28Z

‎25pxNEW LASER SCAN FILTER - MINIMUM NUMBER OF POINTS REQUIRED IN LASER STRIPES

2018-07-11T04:41:59Z

‎25pxNEW LASER SCAN FILTER - MINIMUM NUMBER OF POINTS REQUIRED IN LASER STRIPES

2018-07-06T19:22:32Z

‎25pxNEW - PRESS ACCEPT BUTTON WITHOUT AIMING AT THE PART

2018-07-05T22:36:06Z

‎25pxNEW - HERBER Bender Setup From Solid Model Through a Network (VTube-LASER or VTube-STEP)

2018-07-05T22:35:28Z

‎25pxNEW - HERBER Bender Corrections Through a Network (VTube-LASER Only)

2018-07-05T20:04:13Z

‎Revision 2.9.10

2018-07-05T17:35:54Z

‎25pxNEW LASER SCAN FILTER - MINIMUM NUMBER OF POINTS REQUIRED IN LASER STRIPES

2018-07-05T17:26:59Z

‎25pxNEW LASER SCAN FILTER - MINIMUM NUMBER OF POINTS REQUIRED IN LASER STRIPES

2018-07-05T17:26:16Z

‎25pxNEW LASER SCAN FILTER - MINIMUM NUMBER OF POINTS REQUIRED IN LASER STRIPES

@@ Line 44: / Line 44: @@
 <br><br>
-If you set the MINIMUM point count (see row 18 in the LASER menu on the right) equal to or greater than the MAXIMUM count (see row 8 in the LASER menu on the right), then no data will enter VTube-LASER, and VTube-LASER will play the LASER SCAN FILTER sound when you attempt a scan (see the new feature below).
+If you set the MINIMUM point count value in row 18 so that it is equal to or greater than the MAXIMUM count value in row 8, then no data will enter VTube-LASER, and VTube-LASER will play the LASER SCAN FILTER sound when you attempt a scan (see the new feature below).
 </td>

@@ Line 44: / Line 44: @@
 <br><br>
-If you set the MINIMUM point count (see row 18 in the LASER menu on the right) to equal to or greater than the MAXIMUM count (see row 8 in the LASER menu on the right), then no data will enter VTube-LASER, and VTube-LASER will play the LASER SCAN FILTER sound when you attempt a scan (see the new feature below).
+If you set the MINIMUM point count (see row 18 in the LASER menu on the right) equal to or greater than the MAXIMUM count (see row 8 in the LASER menu on the right), then no data will enter VTube-LASER, and VTube-LASER will play the LASER SCAN FILTER sound when you attempt a scan (see the new feature below).
 </td>

@@ Line 44: / Line 44: @@
 <br><br>
-If you set the minimum point count to equal to or greater than the MAXIMUM count (see row 8 in the LASER menu), then no data will enter VTube-LASER, and VTube-LASER will play the LASER SCAN FILTER sound when you attempt a scan (see the new feature below).
+If you set the MINIMUM point count (see row 18 in the LASER menu on the right) to equal to or greater than the MAXIMUM count (see row 8 in the LASER menu on the right), then no data will enter VTube-LASER, and VTube-LASER will play the LASER SCAN FILTER sound when you attempt a scan (see the new feature below).
 </td>

@@ Line 99: / Line 99: @@
 * For the FARO scanner, this is the red button.<br><br><br>
-We have redesigned the scanning engine so it no longer requires this in-range scanning position.<br><br><b>As of this version, VTube-LASER will watch for and react to the accept button press even if no laser data is incoming.</b>
+We redesigned the scanning engine so it no longer requires this in-range scanning position.<br><br><b>As of this version, VTube-LASER will watch for and react to the accept button press even if no laser data is incoming.</b>
 </td>

@@ Line 153: / Line 153: @@
 Use this new feature to import solid models into HERBER bender controls.<br><br>
 <b>Bender setup for the HERBER works through either VTube-LASER or VTube-STEP</b>
 </td>

← Older revision		Revision as of 22:35, 5 July 2018
Line 124:		Line 124:

	<b>Bender corrections only work through VTube-LASER. (Not VTube-STEP)</b>		<b>Bender corrections only work through VTube-LASER. (Not VTube-STEP)</b>
		+
		+	<br>
		+	See [[VTube HERBER Bender Correction (MES Protocol)]]
		+
	</td>		</td>

@@ Line 6: / Line 6: @@
 ==Revision 2.9.10==
-Release Date: July 4, 2018<br>
+Release Date: July 5, 2018<br>
-Current Build: 12
+Current Build: 14
 * Back to [[VTube-LASER]]

@@ Line 41: / Line 41: @@
 The default minimum is now 5 points per stripe.<br><br>
-[[image:laser stripe with 5 vertices minimum.png|300px]]
+[[image:laser stripe with 5 vertices minimum.png|400px]]
 <br><br>

@@ Line 35: / Line 35: @@
 You can experiment with larger numbers to have a greater culling effect if you experience lone outliers.<br><br>
-The new value can be entered and adjusted in the MEASURE SETUP / LASER tab menu.<br><br>
+The new value can be entered and adjusted in the MEASURE SETUP / LASER tab menu. In this example, we entered "40" points required.<br><br>
 [[image:vtl_v2.9.10_minimum_number_of_points_per_stripe_closeup.png]]<br><br>