VTube-LASER v1.77.3 - Revision history

Mcone: /* Other Pages */

2012-08-08T03:46:40Z

‎Other Pages

Mcone: /* Revision 1.77.3 */

2012-08-08T03:45:45Z

‎Revision 1.77.3

Mcone at 03:45, 8 August 2012

2012-08-08T03:45:22Z

Mcone: /* 25px NEW: Diameter Model End Lengths Change Based on New "End Adjustment Length" Values in Part Setup */

2012-08-08T03:44:41Z

‎25px NEW: Diameter Model End Lengths Change Based on New "End Adjustment Length" Values in Part Setup

Mcone: /* 25px NEW: Diameter Model End Lengths Change Based on New "End Adjustment Length" Values in Part Setup */

2012-08-08T03:43:44Z

‎25px NEW: Diameter Model End Lengths Change Based on New "End Adjustment Length" Values in Part Setup

Mcone at 03:43, 8 August 2012

2012-08-08T03:43:18Z

Mcone at 03:42, 8 August 2012

2012-08-08T03:42:37Z

New page

<table>
<tr cellpadding=10>
<td width=225>
[[image:vtube-step_logo.jpg|200px]]
==Revision 1.77.3==
* Back to [[VTube-STEP]]
* Back to [[VTube-STEP Revisions]]
* Back to [[VTube-LASER]]

</td>
<td width=300>
[[image:Vtube-laser_1.77.3a.jpg|300px]]
</td>
</tr>
</table>

__NOTOC__

===[[image:Check.jpg|25px]] ENHANCED: View Orientation Control Redesigned===
<table cellpadding=10>
<tr valign=top>
<td width=300>
[[image:vtube_1.77.3_vieworientation_closeup.jpg|250px]]<br><br>
The View Orientation Control has new choices with graphics icons of each axes orientation.<br><br>
You can click on the button or the image to find a new orientation.</td>
<td width=300>
[[image:vtube_1.77.3_vieworientation.jpg|150px]]
</td>
</tr>
</table>

===[[image:Check.jpg|25px]] NEW: Diameter Model End Lengths Change Based on New "End Adjustment Length" Values in Part Setup===
[[image:vtube_1.77.3_EndLengthShortened_Closeup.jpg]]
<table cellpadding=10>
<tr valign=top>
<td width=300>
When the A-End or B-End Adjustment Lengths change, then the diameter model lengths change automatically at the next redraw. This does not change the centerline end point location.</td>
<td width=300>
</td>
</tr>
</table>
[[image:vtube_1.77.3_EndLengthShortened.jpg|500px]]
<br><br>

===[[image:Check.jpg|25px]] REPAIR: The Cut Length Calculation with Non Zero End Adjustments Is Repaired===
[[image:vtube_endlength_cutlength_partsetup.jpg|300px]]
<table cellpadding=10>
<tr valign=top>
<td width=300>
The End Length Adjustments values are no longer doubled in the Cut Length calculation.</td>
<td width=300>
</td>
</tr>
</table>

==Other Pages==

*Back to the [[VTube]] page

← Older revision		Revision as of 03:46, 8 August 2012
Line 57:		Line 57:
	==Other Pages==		==Other Pages==

−	*Back to the [[VTube]] page	+	*Back to the [[VTube-LASER]] page

@@ Line 5: / Line 5: @@
 ==Revision 1.77.3==
 * Back to [[VTube-STEP]]
-* Back to [[VTube-STEP Revisions]]
+* Back to [[VTube Software Updates]]
 * Back to [[VTube-LASER]]

@@ Line 2: / Line 2: @@
 <tr cellpadding=10>
 <td width=225>
-[[image:vtube-step_logo.jpg|200px]]
+[[image:vtube-laser_logo.jpg|300px]]
 ==Revision 1.77.3==
 * Back to [[VTube-STEP]]

@@ Line 32: / Line 32: @@
 ===[[image:Check.jpg|25px]] NEW: Diameter Model End Lengths Change Based on New "End Adjustment Length" Values in Part Setup===
-[[image:vtube_laser_1.77.3_EndLengthShortened_Closeup.jpg]]
+[[image:vtube_laser_1.77.3_EndLengthShortened_Closeup.jpg|400px]]
 <table cellpadding=10>
 <tr valign=top>

@@ Line 10: / Line 10: @@
 </td>
 <td width=300>
-[[image:Vtube-laser_1.77.3a.jpg|300px]]
+[[image:Vtube-laser_1.77.3.jpg|300px]]
 </td>
 </tr>