Robot Integration Standard 1 - Revision history

Mcone: /* Formalization of Robot Specification */

2008-07-24T19:37:44Z

‎Formalization of Robot Specification

Mcone: /* Other Pages */

2008-07-24T19:30:35Z

‎Other Pages

Mcone: /* Command Setup for Robot Type 1 */

2008-07-24T19:30:22Z

‎Command Setup for Robot Type 1

Mcone at 19:28, 24 July 2008

2008-07-24T19:28:39Z

New page

[[image:Industrial_robot.jpg|200px|right]]
[[image:cncbender_logo.jpg|400px]]

CNC Bender can integrate to robots for both loading and unloading.

== Formalization of Robot Specification ==

As of CNC Bender v11-20080725, we have standardized a robot specification that is useful for both LOAD and UNLOAD.

==Logic Flow for Robot Type 1 Integration==

You can view sample LOAD and UNLOAD logic here for our standard robot (type 1) integration.

<br>

<table cellpadding="15" width = 450>
<tr valign="top">
<td bgcolor="#abbad1" width = 200>
[[image:Cncbender_robot1_unloadlogic_thumb.jpg|200px]]
</td>
<td bgcolor="#e3e4f5">
[http://www.advancedtubular.com/cncbender/StandardCNCBenderRobotUnloadLogic.pdf View Unload Logic PDF document]
</td>
</tr>

<tr valign="top">
<td bgcolor="#abbad1" width = 200>
[[image:Cncbender_robot1_loadlogic_thumb.jpg|200px]]
</td>
<td bgcolor="#e3e4f5">
[http://www.advancedtubular.com/cncbender/StandardCNCBenderRobotLoadLogic.pdf View Load Logic PDF document]
</td>
</tr>

</table>

==Command Setup for Robot Type 1==

This chart shows an example of of the the command set that is used by CNC Bender to integrate to standard robots.<br><br>
<i>
(Note that the input/output point assignment is for bender 16188. The assignment may vary slightly between benders. However, the COMDEF and CIO names will remaine the same):
</i>
<br><br>
[[image:Cncbender_commandsetup_robot_type1.jpg]]
<br><br>
The '''robot_check_fault''' secondary process is told to start just before the last bend begins, then told to disable at the start of the next cycle (next part). The process looks something like this:

<pre>
[if] and, BeyondPowerOnTime=2000, input=Input_RobotFault_End
[immediate_message]IMMEDIATE SHUTDOWN - Robot Fault - digital_input_205:
OutputControlOff
[SECONDARY_PROCLIST] robot_check_fault, disable
[end]
</pre>

@@ Line 58: / Line 58: @@
 == Other Pages ==
-Back to [[CNC Bender Robot Integration]] page
+*Back to [[CNC Bender Robot Integration]] page
-Back to [[CNC Bender]] page
+*Back to [[CNC Bender]] page

← Older revision		Revision as of 19:30, 24 July 2008
Line 53:		Line 53:
	[end]		[end]
	</pre>		</pre>
		+
		+
		+
		+	== Other Pages ==
		+
		+	Back to [[CNC Bender Robot Integration]] page
		+	Back to [[CNC Bender]] page

← Older revision		Revision as of 19:37, 24 July 2008
Line 7:		Line 7:

	As of CNC Bender v11-20080725, we have standardized a robot specification that is useful for both LOAD and UNLOAD.		As of CNC Bender v11-20080725, we have standardized a robot specification that is useful for both LOAD and UNLOAD.
		+	<br><br>

	==Logic Flow for Robot Type 1 Integration==		==Logic Flow for Robot Type 1 Integration==