Revision: Benderlink for BLM 5.3 - Revision history

Mcone: /* 25px NEW - Click on LEDs to Toggle to Measuring Center Monitoring */

2015-10-14T22:03:25Z

‎25px NEW - Click on LEDs to Toggle to Measuring Center Monitoring

2015-10-14T22:03:14Z

‎25px NEW - Large Green LED to Show Measuring Center Monitoring

2015-10-14T22:02:36Z

‎25px FIXED - Ping Port Confirmation Works in Newer Windows

2015-10-14T22:01:42Z

‎25px NEW - Message Warning for Ports That Cannot Open

2015-10-14T22:01:28Z

‎25px NEW - Message Warning for Ports That Cannot Open

2015-10-14T22:01:03Z

‎25px NEW - Switch for "Do Not Allow Measuring Center to Change End Lengths"

2015-10-14T22:00:35Z

‎25px NEW - Switch for Do Not Allow Measuring Center to Change End Lengths

2015-10-14T21:59:46Z

‎25px NEW - Large Green LED to Show Measuring Center Monitoring

2015-10-14T21:59:36Z

‎25px NEW - Communications Transfers No Longer Change the BLM Radius Levels

2015-10-14T21:59:10Z

‎25px NEW - Communications Transfers No Longer Change the BLM Radius Levels

@@ Line 67: / Line 67: @@
 </table>
 <br><br>
 ===[[image:Check.jpg|25px]] NEW - Click on LEDs to Toggle to Measuring Center Monitoring===

← Older revision		Revision as of 22:03, 14 October 2015
Line 20:		Line 20:
	<br><br>		<br><br>

−
−	~~===[[image:Check.jpg\|25px]] NEW - Large Green LED to Show Measuring Center Monitoring===~~
−	~~<table width=700>~~
−
−	~~<tr>~~
−	~~<td width=300>~~
−	~~A new larger green LED port indicator to show that Benderlink is monitoring for measuring center communications is added to the interface.<br><br>~~
−	~~It is also possible to click on the LED to toggle the measuring center monitor state.~~
−	~~</td>~~
−	~~<td width=400>~~
−	~~[[image:benderlinkblm_v5.3_large_led.png\|400px]]~~
−	~~</td>~~
−	~~</tr>~~
−
−	~~</table>~~
−	~~<br><br>~~

	===[[image:Check.jpg\|25px]] NEW - Communications Transfers No Longer Change the BLM Radius Levels===		===[[image:Check.jpg\|25px]] NEW - Communications Transfers No Longer Change the BLM Radius Levels===

@@ Line 99: / Line 99: @@
 <br><br>
-===[[image:Check.jpg|25px]] FIXED - Ping Port Confirmation Works in Newer Windows===
+===[[image:Check.jpg|25px]] FIXED - Ping Port Confirmation Works in Windows 7, 8, 8.1, 10===
 <table width=700>

@@ Line 115: / Line 115: @@
 <br><br>
-===[[image:Check.jpg|25px]] NEW - Message Warning for Ports That Cannot Open===
+===[[image:Check.jpg|25px]] NEW - Message Warning for COM Ports That Cannot Open===
 <table width=700>

@@ Line 120: / Line 120: @@
 <tr>
 <td width=300>
-When a port to the measuring center cannot open, Benderlink now displays a message that a problem occurred.
+When a COM port to the measuring center cannot open, Benderlink now displays a message that a problem occurred.
 </td>
 <td width=400>
@@ Line 129: / Line 129: @@
 </table>
 <br><br>
 ==Other Pages==

@@ Line 58: / Line 58: @@
 <tr>
 <td width=300>
-During CORRECTION of parts with extra material on the ends, it is helpful to not allow the end lengths to change.  This keeps the carriage in approximately the same start position.<br><br>
+During CORRECTION of parts with extra material on the ends, it is helpful to not allow the end lengths to change.  This keeps the carriage in approximately the same start position even after corrections are applied.<br><br>
 This version of Benderlink now includes this checkbox switch to turn this feature on or off.
 </td>

@@ Line 53: / Line 53: @@
 <br><br>
-===[[image:Check.jpg|25px]] NEW - Switch for Do Not Allow Measuring Center to Change End Lengths===
+===[[image:Check.jpg|25px]] NEW - Switch for "Do Not Allow Measuring Center to Change End Lengths"===
 <table width=700>

← Older revision		Revision as of 21:59, 14 October 2015
Line 37:		Line 37:
	<br><br>		<br><br>

		+	===[[image:Check.jpg\|25px]] NEW - Communications Transfers No Longer Change the BLM Radius Levels===
		+	<table width=700>

		+	<tr>
		+	<td width=300>
		+	Setting or changing BLM radius levels could easily cause radius level mix ups during corrections loops. The radius levels are no longer touched or changed during transfer. <br><br>
		+	Not setting the radius levels is no problem - since corrections loops targets the LRA data only anyway.
		+	</td>
		+	<td width=400>
		+	[[image:blinkblm_electric_verticalshift.png\|400px]]
		+	</td>
		+	</tr>

		+	</table>
		+	<br><br>

	===[[image:Check.jpg\|25px]] NEW - Switch for Do Not Allow Measuring Center to Change End Lengths===		===[[image:Check.jpg\|25px]] NEW - Switch for Do Not Allow Measuring Center to Change End Lengths===

← Older revision		Revision as of 21:59, 14 October 2015
Line 118:		Line 118:


−
−	~~===[[image:Check.jpg\|25px]] NEW - Communications Transfers No Longer Change the BLM Radius Levels===~~
−	~~<table width=700>~~
−
−	~~<tr>~~
−	~~<td width=300>~~
−	~~Setting or changing BLM radius levels could easily cause radius level mix ups during corrections loops. The radius levels are no longer touched or changed during transfer. <br><br>~~
−	~~Not setting the radius levels is no problem - since corrections loops targets the LRA data only anyway.~~
−	~~</td>~~
−	~~<td width=400>~~
−	~~[[image:blinkblm_electric_verticalshift.png\|400px]]~~
−	~~</td>~~
−	~~</tr>~~
−
−	~~</table>~~
−	~~<br><br>~~

	==Other Pages==		==Other Pages==

@@ Line 128: / Line 128: @@
 </td>
 <td width=400>
-[[blinkblm_electric_verticalshift.png|400px]]
+[[image:blinkblm_electric_verticalshift.png|400px]]
 </td>
 </tr>