PINES NC - Revision history

Mcone: /* LIMTATION */

2007-02-04T17:59:55Z

‎LIMTATION

Mcone at 17:59, 4 February 2007

2007-02-04T17:59:03Z

Mcone at 17:58, 4 February 2007

2007-02-04T17:58:31Z

Mcone at 17:57, 4 February 2007

2007-02-04T17:57:14Z

Mcone at 00:37, 30 January 2007

2007-01-30T00:37:20Z

Mcone at 00:37, 30 January 2007

2007-01-30T00:37:04Z

Mcone at 00:36, 30 January 2007

2007-01-30T00:36:42Z

Mcone at 00:36, 30 January 2007

2007-01-30T00:36:22Z

Mcone at 23:52, 29 January 2007

2007-01-29T23:52:55Z

Mcone at 23:52, 29 January 2007

2007-01-29T23:52:33Z

New page

The PINES NC (numerical control) control is a BEND angle controller. It does not communicate with measuring centers.

--[[User:Mcone|Mcone]] 18:52, 29 January 2007 (EST)

@@ Line 6: / Line 6: @@
 This type of bender is known to be an inexpensive solution compared to full CNC (3 or more controlled axes - Carriage Feed, Carriage Rotate, Bend Arm).  These benders fit applications where there are few part shapes produced overall, or single bend applications.
-===LIMTATION===
+===LIMITATION===
 For applications that require multiple bends with rotation (twist) between the bend planes, then this style of bender can severly limit production capabilities - potentially costing much more in the long-run than the more expensive CNC benders.
 --[[User:Mcone|Mcone]] 18:52, 29 January 2007 (EST)

@@ Line 3: / Line 3: @@
 http://www.pines-mfg.com/images/model1142.jpg
 This type of bender is known to be an inexpensive solution compared to full CNC (3 or more controlled axes - Carriage Feed, Carriage Rotate, Bend Arm).  These benders fit applications where there are few part shapes produced overall, or single bend applications.
 For applications that require multiple bends with rotation (twist) between the bend planes, then this style of bender can severly limit production capabilities - potentially costing much more in the long-run than the more expensive CNC benders.
 --[[User:Mcone|Mcone]] 18:52, 29 January 2007 (EST)

@@ Line 3: / Line 3: @@
 http://www.pines-mfg.com/images/model1142.jpg
-This type of bender is known to be an inexpensive solution compared to full CNC (3 or more controlled axes).  These benders fit applications where there are few part shapes produced overall, or single bend applications.
+This type of bender is known to be an inexpensive solution compared to full CNC (3 or more controlled axes - Carriage Feed, Carriage Rotate, Bend Arm).  These benders fit applications where there are few part shapes produced overall, or single bend applications.
-For applications that require multiple bends with rotation (twist) between the bend planes, then this style of bender can severly limits production capabilities.
+For applications that require multiple bends with rotation (twist) between the bend planes, then this style of bender can severly limit production capabilities - potentially costing much more in the long-run than the more expensive CNC benders.
 --[[User:Mcone|Mcone]] 18:52, 29 January 2007 (EST)

← Older revision		Revision as of 17:57, 4 February 2007
Line 2:		Line 2:

	http://www.pines-mfg.com/images/model1142.jpg		http://www.pines-mfg.com/images/model1142.jpg
		+
		+	This type of bender is known to be an inexpensive solution compared to full CNC (3 or more controlled axes). These benders fit applications where there are few part shapes produced overall, or single bend applications.
		+
		+	For applications that require multiple bends with rotation (twist) between the bend planes, then this style of bender can severly limits production capabilities.

	--[[User:Mcone\|Mcone]] 18:52, 29 January 2007 (EST)		--[[User:Mcone\|Mcone]] 18:52, 29 January 2007 (EST)

@@ Line 1: / Line 1: @@
 The PINES NC (numerical control) control is a BEND angle controller.  It does not communicate with other computers and measuring centers.
-"http://www.pines-mfg.com/images/model1142.jpg"
+http://www.pines-mfg.com/images/model1142.jpg
 --[[User:Mcone|Mcone]] 18:52, 29 January 2007 (EST)

← Older revision		Revision as of 00:36, 30 January 2007
Line 1:		Line 1:
	The PINES NC (numerical control) control is a BEND angle controller. It does not communicate with other computers and measuring centers.		The PINES NC (numerical control) control is a BEND angle controller. It does not communicate with other computers and measuring centers.

		+	<img border="0" src="http://www.pines-mfg.com/images/model1142.jpg">

	--[[User:Mcone\|Mcone]] 18:52, 29 January 2007 (EST)		--[[User:Mcone\|Mcone]] 18:52, 29 January 2007 (EST)

← Older revision		Revision as of 23:52, 29 January 2007
Line 1:		Line 1:
−	The PINES NC (numerical control) control is a BEND angle controller. It does not communicate with measuring centers.	+	The PINES NC (numerical control) control is a BEND angle controller. It does not communicate with other computers and measuring centers.


	--[[User:Mcone\|Mcone]] 18:52, 29 January 2007 (EST)		--[[User:Mcone\|Mcone]] 18:52, 29 January 2007 (EST)