Measuring Coping - Revision history

Mcone at 16:37, 21 March 2016

2016-03-21T16:37:45Z

2016-03-21T16:37:05Z

2016-03-20T21:26:16Z

2016-03-20T21:21:58Z

‎STEP 7: Setup and Align the Measured Part

2016-03-20T21:21:07Z

‎STEP 7: Setup and Align the Measured Part

2016-03-20T21:19:56Z

‎STEP 7: Setup and Align the Measured Part

2016-03-20T21:18:36Z

‎STEP 7: Setup and Align the Measured Part

2016-03-20T21:18:10Z

‎STEP 7: Setup and Align the Measured Part

2016-03-20T21:16:29Z

‎STEP 6: Switch to VTube-LASER Mode and Measure the Part

2016-03-20T21:07:27Z

‎STEP 6: Switch to VTube-LASER Mode and Measure the Part

← Older revision		Revision as of 16:37, 21 March 2016
Line 18:		Line 18:

	This article discusses how to measure a coping along with the tube shape in VTube-LASER. The method used is to measure the coping as if it were an additional straight on the end of the tube.<br><br>		This article discusses how to measure a coping along with the tube shape in VTube-LASER. The method used is to measure the coping as if it were an additional straight on the end of the tube.<br><br>
−	In order to do this, ~~the~~ pipe ~~straight~~ that joins the main pipe at the coping can be treated like and extra end-straight on the pipe in VTube-LASER	+	In order to do this, an adapter pipe that joins the main pipe at the coping can be treated like and extra end-straight on the pipe in VTube-LASER

← Older revision		Revision as of 16:37, 21 March 2016
Line 17:		Line 17:


−	This article discusses how to measure a coping along with the tube shape in VTube-LASER. The method is ~~to find a way~~ to measure the coping as if it were an additional straight on the end of the tube.<br><br>	+	This article discusses how to measure a coping along with the tube shape in VTube-LASER. The method used is to measure the coping as if it were an additional straight on the end of the tube.<br><br>
	In order to do this, the pipe straight that joins the main pipe at the coping can be treated like and extra end-straight on the pipe in VTube-LASER		In order to do this, the pipe straight that joins the main pipe at the coping can be treated like and extra end-straight on the pipe in VTube-LASER

@@ Line 2: / Line 2: @@
 <tr cellpadding=10>
 <td width=225>
 [[image:vtube-laser_logo_1.96.png|200px]]
 * Back to [[VTube-LASER]]
 </td>
@@ Line 13: / Line 15: @@
 __NOTOC__
 This article discusses how to measure a coping along with the tube shape in VTube-LASER.  The method is to find a way to measure the coping as if it were an additional straight on the end of the tube.<br><br>

@@ Line 137: / Line 137: @@
 </tr>
 <tr valign=top>
 <td width=300>

@@ Line 131: / Line 131: @@
 In this alignment, we used 321 Plane Line Point alignment to lock the tube to itself, and allow all the error to float to the coping end of the tube.<br><br>
 The pink tube is the measured aligned tube.  It allows you to visualize how far out of the envelope the coping is when the adapter is attached.<br><br>
-You can also print out a Bender Corrections Only report to see the exact rotational adjusting to make to the part when cutting the coping.</td>
+</td>
 <td>
 [[image:vtube-laser_v2.3_align_inspect_coping_adapter_part.png|600px]]<br><br>
 [[image:vtube-laser_v2.3_report_coping_adapter_part.png|600px]]<br><br>
 </td>
 </tr>
-<tr>
 </table>
 <br>

@@ Line 116: / Line 116: @@
 <td>
 [[image:vtube-laser_v2.3_measure_coping_adapter_part.png|600px]]
 </td>
 </tr>

@@ Line 111: / Line 111: @@
 <tr valign=top>
 <td width=300>
-Switch to VTube-LASER, temporarily attach the adapter to the coping on the part, then measure and qualify the entire part with the adapter.<br><br>
+Switch to VTube-LASER, attach the adapter (temporarily) to the coping on the part, then measure and qualify the entire part with the adapter.<br><br>
 </td>
 <td>