Lube Machine At Part Count - Revision history

Mcone at 01:16, 13 July 2007

2007-07-13T01:16:17Z

Mcone at 01:16, 13 July 2007

2007-07-13T01:16:07Z

Mcone at 03:45, 20 July 2006

2006-07-20T03:45:18Z

Mcone at 03:44, 20 July 2006

2006-07-20T03:44:50Z

Mcone at 03:43, 20 July 2006

2006-07-20T03:43:27Z

Mcone at 03:43, 20 July 2006

2006-07-20T03:43:11Z

Mcone at 03:41, 20 July 2006

2006-07-20T03:41:58Z

Mcone at 03:30, 20 July 2006

2006-07-20T03:30:53Z

Mcone at 03:25, 20 July 2006

2006-07-20T03:25:03Z

New page

__toc__

===What is It?===
This property allows [[CNC Processor]] to switch the mandrel lube output to ON after a pre-programmed number of parts have run.

===Value===
The value is set to milliseconds like this:

<pre>Lube Machine At Part Count= 500</pre>

In this case, the machine lube will activate after each 500 parts run on the machine.

===Alternative Properties===

// How many accumulated parts run before
// CNC Processor lubes the machine?
Lube Machine At Part Count= 500
Use Bend Count For Machine Lube= 1
Lube Machine At Bend Count= 1000

// How many accumulated parts run before
// CNC Processor lubes the machine?
Lube Machine At Part Count= 100

[CIO]
CIO Name Of Input Clamp Die Close=Input_ClampIsClosed_Begin
CIO Name Of Input Pressure Die Home=Input_PressureDieIsHome_End
CIO Name Of Input Pressure Die Close=Input_PressureDieIsClosed_Begin
CIO Name Of Input Carriage Cross Slide Advance=Input_CarriageCrossSlideIsAdvanced_End
CIO Name Of Input Release Button= Input_Release_Button_End
CIO Name Of Output Release Illuminate= Output_Release_Illuminate
CIO Name Of Boost Bottom Advance= Output_BoostBottom_Advance
CIO Name Of Boost Top Advance= Output_BoostTop_Advance
CIO Name Of Bend Positive= MOVE_BEND_POS_RELATIVE
CIO Name Of Output Machine Lube=Output_MachineLube_Repeat

[SOUND]
INIT=cncbender_initialized.wav
AE=all_axes_enabled.wav
AD=all_axes_disabled.wav
WRE=warning_range_error_encountered.wav
CH=cycle_hold.wav
CS=cycle_start.wav
MM=manual_mode.wav
SM=step_mode.wav
AM=auto_mode.wav
SMMF=switch_to_manual_mode_first.wav

[PRIORITY]
Master Loop Priority=10000

</pre>

Note that remarks may be added to the file with lines preceded by double forward slashes.

<pre>// How long does the machine loop output enable?</pre>

 

===Properties Definition===
Read about individual properties: 
[[Lube Machine At Part Count]] 
[[Use Bend Count For Machine Lube]] 
[[Lube Machine At Bend Count]] 

--[[User:Mcone|Mcone]] 23:18, 19 July 2006 (EDT)

@@ Line 1: / Line 1: @@
-''As of v10-20070711 (July 11, 2007, this property is obsolete and is no longer available.
+''As of v10-20070711 (July 11, 2007), this property is obsolete and is no longer available.
 ''
 __toc__

← Older revision		Revision as of 01:16, 13 July 2007
Line 1:		Line 1:
		+	''As of v10-20070711 (July 11, 2007, this property is obsolete and is no longer available.
		+	''
	__toc__		__toc__

@@ Line 15: / Line 15: @@
 Two alternative properties are...
-<l>
+<ol>
 <li>Use Bend Count For Machine Lube</li>
 <li>Lube Machine At Bend Count</li>
-</l>
+</ol>

@@ Line 15: / Line 15: @@
 Two alternative properties are...
-<ul>
+<l>
 <li>Use Bend Count For Machine Lube</li>
 <li>Lube Machine At Bend Count</li>
-</ul>
+</l>

@@ Line 20: / Line 20: @@
 </ul>
-<ul>
 If [[Use Bend Count For Machine Lube]] value is set to 0 then the Lube Machine At Part Count property will be used.  Set the [[Use Bend Count For Machine Lube]] property to equal 1 to set CNC Processor to use the "Lube Machine At Bend Count" property.<br>
 <br>

@@ Line 13: / Line 13: @@
 ===Alternative Properties===
-// How many accumulated parts run before
+<pre>Use Bend Count For Machine Lube
-// CNC Processor lubes the machine?
+Lube Machine At Bend Count
-Lube Machine At Part Count= 500
-Use Bend Count For Machine Lube= 1
-Lube Machine At Bend Count= 1000
-−
-−
-// How many accumulated parts run before
-// CNC Processor lubes the machine?
-Lube Machine At Part Count= 100
-−
-−
-[CIO]
-CIO Name Of Input Clamp Die Close=Input_ClampIsClosed_Begin
-CIO Name Of Input Pressure Die Home=Input_PressureDieIsHome_End
-CIO Name Of Input Pressure Die Close=Input_PressureDieIsClosed_Begin
-CIO Name Of Input Carriage Cross Slide Advance=Input_CarriageCrossSlideIsAdvanced_End
-CIO Name Of Input Release  Button= Input_Release_Button_End
-CIO Name Of Output Release Illuminate= Output_Release_Illuminate
-CIO Name Of Boost Bottom Advance= Output_BoostBottom_Advance
-CIO Name Of Boost Top Advance= Output_BoostTop_Advance
-CIO Name Of Bend Positive= MOVE_BEND_POS_RELATIVE
-CIO Name Of Output Machine Lube=Output_MachineLube_Repeat
-−
-−
-[SOUND]
-INIT=cncbender_initialized.wav
-AE=all_axes_enabled.wav
-AD=all_axes_disabled.wav
-WRE=warning_range_error_encountered.wav
-CH=cycle_hold.wav
-CS=cycle_start.wav
-MM=manual_mode.wav
-SM=step_mode.wav
-AM=auto_mode.wav
-SMMF=switch_to_manual_mode_first.wav
-−
-[PRIORITY]
-Master Loop Priority=10000
-−
 </pre>
+If [[Use Bend Count For Machine Lube]] value is set to 0 then the Lube Machine At Part Count property will be used.  Set the [[Use Bend Count For Machine Lube]] property to equal 1 to set CNC Processor to use the "Lube Machine At Bend Count" property.<br>
-Note that remarks may be added to the file with lines preceded by double forward slashes.
-−
-<pre>// How long does the machine loop output enable?</pre>
-−
-−
 <br>
-===Properties Definition===
+--[[User:Mcone|Mcone]] 23:30, 19 July 2006 (EDT)
-Read about individual properties:<br>
-[[Lube Machine At Part Count]]<br>
-[[Use Bend Count For Machine Lube]]<br>
-[[Lube Machine At Bend Count]]<br>
-−
-−
---[[User:Mcone|Mcone]] 23:18, 19 July 2006 (EDT)