How to Setup for Supravision Network Protocol - Revision history

Mcone: /* =Other Pages */

2012-09-12T18:42:47Z

‎=Other Pages

2012-09-12T18:42:39Z

‎Step 7: Press OK to Exit the Window

2012-09-12T18:41:55Z

2012-09-12T18:41:37Z

‎Step 7: Press OK to Exit the Window

2012-09-12T18:40:53Z

‎Step 6: Switch to the Supravision Tab Menu

2012-09-12T18:38:14Z

‎Step 5: Switch to the Measuring Center Protocol Tab Menu

2012-09-12T18:35:48Z

‎Step 4: Switch to the Measuring Center Name Tab Menu

2012-09-12T18:32:04Z

‎Step 3: Setup the Bender Communication Parameters

2012-09-12T18:20:17Z

‎Step 3: Setup the Bender Communication Parameters

2012-09-12T18:19:35Z

‎Step 2: Enter the Benderlink Network

@@ Line 79: / Line 79: @@
 Benderlink is now ready to communicate automatically with the EL benders programmed into your network.  The Monitor Status LED will switch on and off indicating that it is watching for measuring center commands.
-==Other Pages=
+==Other Pages==
 *Back to [[Benderlink for Eaton Leonard]]

@@ Line 77: / Line 77: @@
-Benderlink is now ready to communicate automatically with the EL benders programmed into your network.
+Benderlink is now ready to communicate automatically with the EL benders programmed into your network.  The Monitor Status LED will switch on and off indicating that it is watching for measuring center commands.
-−
-−
 ==Other Pages=
 *Back to [[Benderlink for Eaton Leonard]]

← Older revision		Revision as of 18:41, 12 September 2012
Line 78:		Line 78:

	Benderlink is now ready to communicate automatically with the EL benders programmed into your network.		Benderlink is now ready to communicate automatically with the EL benders programmed into your network.
		+
		+
		+
		+	==Other Pages=
		+
		+	*Back to [[Benderlink for Eaton Leonard]]

← Older revision		Revision as of 18:41, 12 September 2012
Line 75:		Line 75:

	[[image:BlinkEL_MainWindow_MeasuringCenter.jpg]]		[[image:BlinkEL_MainWindow_MeasuringCenter.jpg]]
		+
		+
		+	Benderlink is now ready to communicate automatically with the EL benders programmed into your network.

← Older revision		Revision as of 18:40, 12 September 2012
Line 67:		Line 67:

	[[image:BlinkEL_Supravision.jpg]]		[[image:BlinkEL_Supravision.jpg]]
		+
		+
		+
		+	== Step 7: Press OK to Exit the Window==
		+
		+	The main window will change to show the Measuring Center setup:
		+
		+	[[image:BlinkEL_MainWindow_MeasuringCenter.jpg]]

← Older revision		Revision as of 18:38, 12 September 2012
Line 57:		Line 57:

	[[image:BlinkEL_MeasuringCenterProtocol.jpg]]		[[image:BlinkEL_MeasuringCenterProtocol.jpg]]
		+
		+
		+	== Step 6: Switch to the Supravision Tab Menu==
		+
		+	*Set the monitor frequency from 2 to 5 seconds
		+	*Set the max benders to scan (set to your highest bender number)
		+	*Set the Supravision Network path that Supravision uses to drop SVNET files.
		+	*Enable the Monitor for SV Commands checkbox
		+
		+	[[image:BlinkEL_Supravision.jpg]]

← Older revision		Revision as of 18:35, 12 September 2012
Line 50:		Line 50:

	[[image:BlinkEL_MeasuringCenterName.jpg]]		[[image:BlinkEL_MeasuringCenterName.jpg]]
		+
		+
		+	== Step 5: Switch to the Measuring Center Protocol Tab Menu==
		+
		+	Set the name of the measuring center protocol to "Supravision Network".
		+
		+	[[image:BlinkEL_MeasuringCenterProtocol.jpg]]

← Older revision		Revision as of 18:32, 12 September 2012
Line 43:		Line 43:

	[[image:BlinkEL_EditBenderNetwork.jpg]]		[[image:BlinkEL_EditBenderNetwork.jpg]]
		+
		+
		+	== Step 4: Switch to the Measuring Center Name Tab Menu==
		+
		+	Set the name of the measuring center to one of the types that uses the Supravision Network protocol.
		+
		+	[[image:BlinkEL_MeasuringCenterName.jpg]]

@@ Line 37: / Line 37: @@
 == Step 3: Setup the Bender Communication Parameters==
-Each bender number must be unique.
+* Each bender number must be unique.
-The name will display in the user interface of Benderlink.
+* The name will display in the user interface of Benderlink.
-The COM port is the port number assigned to communicate with this bender.
+* The COM port is the port number assigned to communicate with this bender.
 [[image:BlinkEL_EditBenderNetwork.jpg]]

← Older revision		Revision as of 18:19, 12 September 2012
Line 33:		Line 33:

	[[image:BlinkEL_BenderNetwork.jpg]]		[[image:BlinkEL_BenderNetwork.jpg]]
		+
		+
		+	== Step 3: Setup the Bender Communication Parameters==
		+
		+	Each bender number must be unique.
		+	The name will display in the user interface of Benderlink.
		+	The COM port is the port number assigned to communicate with this bender.
		+
		+	[[image:BlinkEL_EditBenderNetwork.jpg]]