Hopper Logic - Revision history

Mcone: /* LOW LEVEL OPTION:
HOPPER PART PRESENT COMDEF NAME */

2008-10-01T23:15:13Z

‎LOW LEVEL OPTION: <br>HOPPER PART PRESENT COMDEF NAME

2008-10-01T23:11:49Z

‎LOW LEVEL OPTION: HOPPER PART PRESENT COMDEF NAME

2008-10-01T23:11:35Z

‎LOW LEVEL OPTION: HOPPER SECONDARY PROCESS INTERVAL

2008-10-01T23:11:21Z

‎LOW LEVEL OPTION: HOPPER SECONDARY PROCESS NAME

2008-10-01T23:11:10Z

‎PREBEND OPTION: HOPPER ENABLE MODE

2008-10-01T23:10:43Z

‎LOW LEVEL OPTION: HOPPER SECONDARY PROCESS NAME

2008-10-01T22:53:57Z

‎LOW LEVEL OPTION: HOPPER SECONDARY PROCESS INTERVAL

2008-10-01T22:53:35Z

‎PREBEND OPTION: HOPPER ENABLE MODE

2008-10-01T22:52:52Z

‎LOW LEVEL OPTION: HOPPER SECONDARY PROCESS NAME

2008-10-01T22:52:35Z

‎LOW LEVEL OPTION: HOPPER SECONDARY PROCESS INTERVAL

← Older revision		Revision as of 23:15, 1 October 2008
Line 43:		Line 43:
	===LOW LEVEL OPTION: <br>HOPPER PART PRESENT COMDEF NAME===		===LOW LEVEL OPTION: <br>HOPPER PART PRESENT COMDEF NAME===
	Set the Hopper Part Present COMDEF name to be used by the Processlist Builder when Hopper Mode 1 is enabled in Prebending. The default name is "Wait For Part Present In Hopper"		Set the Hopper Part Present COMDEF name to be used by the Processlist Builder when Hopper Mode 1 is enabled in Prebending. The default name is "Wait For Part Present In Hopper"
		+
		+
		+
		+	==Other Pages==
		+
		+	See also the version this was released:
		+	<table>
		+	<tr><td width=150>October 1, 2008</td><td>[[CNC Bender v11-20081001]]</td></tr>
		+	</table>

@@ Line 41: / Line 41: @@
 <br><br>
-===LOW LEVEL OPTION: HOPPER PART PRESENT COMDEF NAME===
+===LOW LEVEL OPTION: <br>HOPPER PART PRESENT COMDEF NAME===
 Set the Hopper Part Present COMDEF name to be used by the Processlist Builder when Hopper Mode 1 is enabled in Prebending.  The default name is "Wait For Part Present In Hopper"

@@ Line 36: / Line 36: @@
 [[image:cncbender_hopper_setup.jpg]]
-===LOW LEVEL OPTION: HOPPER SECONDARY PROCESS INTERVAL===
+===LOW LEVEL OPTION: <br>HOPPER SECONDARY PROCESS INTERVAL===
 Use this option to set the process interval for the hopper secondary process.  The value is in milliseconds.  This value is used by the Hopper 1 mode.   If Hopper Mode 1 is enabled, then this interval is used to control how often the hopper secondary process runs.  Increase this value to decrease the load on the CPU, and also to control, for example, how often the blade moves up and down.

@@ Line 31: / Line 31: @@
 ----
-===LOW LEVEL OPTION: HOPPER SECONDARY PROCESS NAME===
+===LOW LEVEL OPTION: <br>HOPPER SECONDARY PROCESS NAME===
 Use this option to set the process name for the processlist that controls the hopper.  This name is used by Hopper Mode 1 in Prebend.  If Hopper Mode 1 is enabled, then this name is used to start a secondary process at the beginning of the part program to operate the hopper.  The most common use is to control the up and down motion of the tube lift blade in response to a part present input prox switch.
 <br><br>

@@ Line 19: / Line 19: @@
 __NOTOC__
-===PREBEND OPTION: HOPPER ENABLE MODE===
+===PREBEND OPTION:<br>HOPPER ENABLE MODE===
 Hopper Mode 1 uses the hopper name set in the Low Level options to run a secondary process that will handle the hopper operations while the bender is running.  This mode will inert a "Wait For Part Present In Hopper" COMDEF.  The name can be changed in Low Level setup.
 <br><br>

← Older revision		Revision as of 22:53, 1 October 2008
Line 29:		Line 29:


		+	----

−	~~---~~
	===LOW LEVEL OPTION: HOPPER SECONDARY PROCESS NAME===		===LOW LEVEL OPTION: HOPPER SECONDARY PROCESS NAME===
	Use this option to set the process name for the processlist that controls the hopper. This name is used by Hopper Mode 1 in Prebend. If Hopper Mode 1 is enabled, then this name is used to start a secondary process at the beginning of the part program to operate the hopper. The most common use is to control the up and down motion of the tube lift blade in response to a part present input prox switch.		Use this option to set the process name for the processlist that controls the hopper. This name is used by Hopper Mode 1 in Prebend. If Hopper Mode 1 is enabled, then this name is used to start a secondary process at the beginning of the part program to operate the hopper. The most common use is to control the up and down motion of the tube lift blade in response to a part present input prox switch.

← Older revision		Revision as of 22:52, 1 October 2008
Line 36:		Line 36:
	===LOW LEVEL OPTION: HOPPER SECONDARY PROCESS INTERVAL===		===LOW LEVEL OPTION: HOPPER SECONDARY PROCESS INTERVAL===
	Use this option to set the process interval for the hopper secondary process. The value is in milliseconds. This value is used by the Hopper 1 mode. If Hopper Mode 1 is enabled, then this interval is used to control how often the hopper secondary process runs. Increase this value to decrease the load on the CPU, and also to control, for example, how often the blade moves up and down.		Use this option to set the process interval for the hopper secondary process. The value is in milliseconds. This value is used by the Hopper 1 mode. If Hopper Mode 1 is enabled, then this interval is used to control how often the hopper secondary process runs. Increase this value to decrease the load on the CPU, and also to control, for example, how often the blade moves up and down.
		+
		+	===LOW LEVEL OPTION: HOPPER PART PRESENT COMDEF NAME===
		+	Set the Hopper Part Present COMDEF name to be used by the Processlist Builder when Hopper Mode 1 is enabled in Prebending. The default name is "Wait For Part Present In Hopper"