Feed-Bend Motion Adjust Percent - Revision history

Mcone at 19:48, 3 November 2007

2007-11-03T19:48:57Z

Mcone at 19:06, 3 November 2007

2007-11-03T19:06:48Z

Mcone at 17:15, 3 April 2007

2007-04-03T17:15:38Z

Mcone at 17:05, 3 April 2007

2007-04-03T17:05:46Z

Mcone at 17:05, 3 April 2007

2007-04-03T17:05:14Z

Mcone at 17:04, 3 April 2007

2007-04-03T17:04:59Z

Mcone at 17:04, 3 April 2007

2007-04-03T17:04:31Z

New page

This is a feature that allows for adjusting the Feed/Carriage motion during Feed-Bending for all bend radius levels.

This allows for elongation during bending and prevents bowing or stretching of the material. The features are options are in the [[Overall Bending Options]] menu of the [[BENDING Menu]].

[[image: feed-bend_motion_adjust_multiple_radii.jpg|450px]]

<table cellpadding="15" width = 550>

<tr valign="top">
<td bgcolor="#abbad1" width=150>
Feed-Bend Motion Adjust %
---- 
Floating Point Value
</td>
<td bgcolor="#e3e4f5">
[[image:Feed_Bend_Motion_Adjust_Percent_Closeup.jpg]]
</td>
</tr>

<tr valign="top">
<td bgcolor="#abbad1" width=150>
Using a Value of ZERO
---- 
</td>
<td bgcolor="#e3e4f5">
A value of '''ZERO''' will cause no adjustment in the Feed motion during Feed Bending.
</td>
</tr>

<tr valign="top">
<td bgcolor="#abbad1" width=150>
Using a Value BELOW ZERO
---- 
</td>
<td bgcolor="#e3e4f5">
For example, enter '''-5''' (negative 5) to adjust the Feed motion during Feed bending by '''negative 5 percent'''.

Use this value will accomodate for...

# Extreme elongation that cause the Feed axis to jump after the motion is complete and the bend dies open. (Larger/stiffer tubes)
# Bowing of the smaller diameter tubes.

Decreasing the value too much will likely cause the tube to pull from the chuck.
</td>
</tr>

<tr valign="top">
<td bgcolor="#abbad1" width=150>
Using a Value of ABOVE ZERO
---- 
</td>
<td bgcolor="#e3e4f5">
For example, enter '''5''' (positive 5) to move '''5 percent further''' during Feed Bending..

Increasing the value too much will cause the Feed to attempt to press further for final position, not allowing it to come into position.
</td>
</tr>

</table>

← Older revision		Revision as of 19:48, 3 November 2007
Line 63:		Line 63:
	<br>		<br>
	<br>		<br>
−
−	~~[[Eureka!]]~~

← Older revision		Revision as of 19:06, 3 November 2007
Line 63:		Line 63:
	<br>		<br>
	<br>		<br>
		+
		+	[[Eureka!]]

← Older revision		Revision as of 17:05, 3 April 2007
Line 3:		Line 3:
	This allows for elongation during bending and prevents bowing or stretching of the material. The features are options are in the [[Overall Bending Options]] menu of the [[BENDING Menu]].		This allows for elongation during bending and prevents bowing or stretching of the material. The features are options are in the [[Overall Bending Options]] menu of the [[BENDING Menu]].

−	[[image: feed-bend_motion_adjust_multiple_radii.jpg\|450px~~\|right~~]]	+	[[image: feed-bend_motion_adjust_multiple_radii.jpg\|450px]]

← Older revision		Revision as of 17:04, 3 April 2007
Line 3:		Line 3:
	This allows for elongation during bending and prevents bowing or stretching of the material. The features are options are in the [[Overall Bending Options]] menu of the [[BENDING Menu]].		This allows for elongation during bending and prevents bowing or stretching of the material. The features are options are in the [[Overall Bending Options]] menu of the [[BENDING Menu]].

−	[[image: feed-bend_motion_adjust_multiple_radii.jpg\|450px]]	+	[[image: feed-bend_motion_adjust_multiple_radii.jpg\|450px\|right]]

@@ Line 1: / Line 1: @@
 [[image: feed-bend_motion_adjust_multiple_radii.jpg|450px]]
-This is a feature that allows for adjusting the Feed/Carriage motion during Feed-Bending for all bend radius levels.
+This [[Dynamic Option]] allows for adjusting the Feed/Carriage motion during Feed-Bending for all bend radius levels.
 This allows for elongation during bending and prevents bowing or stretching of the material.  The features are options are in the [[Overall Bending Options]] menu of the [[BENDING Menu]].