Cable Spec 22 - Revision history

Mcone: /* Notes */

2016-10-21T21:58:19Z

‎Notes

2016-10-21T21:57:53Z

‎Notes

2016-10-21T21:57:31Z

2013-12-31T02:27:31Z

2013-12-30T22:48:14Z

2013-12-30T22:44:50Z

2013-12-30T22:25:14Z

2013-12-30T22:24:20Z

@@ Line 42: / Line 42: @@
 * The A row in the Amp Mod IV block (the black rectangular connector) is always on the KEY side of the connector.<br><br>
 * Pin 1 is indicated with an arrow embedded in the plastic of the Amp Mod IV block.<br><br>
-* A wire from A1 to pin 6 is not required for this bender. Some cables will not include that wire.<br><br>
+* A wire from B1 to pin 6 is not required for this bender. Some cables will not include that wire.<br><br>
 * The wire coming out of B3 indicates if the bender is ON or OFF. Pin B3 outputs between 5 and 10 volts DC when the bender is ON. If the bender control is switched on, then the DSR signal at the Benderlink computer's COM port will also show active. The state of the incoming DSR signal can be tested with an RS-232 testing program, like WCom32.exe (You can [http://www.advancedtubular.com/customers/benderlink/WCOM32.zip download WCom32] from our web site.)
 <br><br>

@@ Line 40: / Line 40: @@
 ===Notes===
 * The wire colors can vary from the diagram shown above. It is only important that the wires are connected to the correct points.<br><br>
-* The A row in the Amp Mod U block (the black rectangular connector) is always on the KEY side of the connector.<br><br>
+* The A row in the Amp Mod IV block (the black rectangular connector) is always on the KEY side of the connector.<br><br>
-* Pin 1 is indicated with an arrow embedded in the plastic of the Amp Mod U block.<br><br>
+* Pin 1 is indicated with an arrow embedded in the plastic of the Amp Mod IV block.<br><br>
 * A wire from A1 to pin 6 is not required for this bender. Some cables will not include that wire.<br><br>
 * The wire coming out of B3 indicates if the bender is ON or OFF. Pin B3 outputs between 5 and 10 volts DC when the bender is ON. If the bender control is switched on, then the DSR signal at the Benderlink computer's COM port will also show active. The state of the incoming DSR signal can be tested with an RS-232 testing program, like WCom32.exe (You can [http://www.advancedtubular.com/customers/benderlink/WCOM32.zip download WCom32] from our web site.)

@@ Line 36: / Line 36: @@
 </tr>
 </table>
 ==Other Pages==
 * Back to [[Cable Spec]]s

@@ Line 4: / Line 4: @@
 * This is the wiring schematic for Cable Spec 22 used in MQ41 benders.
 * This is a 15 foot cable.
-* Use yellow sheath if possible.
+* Yellow sheath is preferred.
 * Use twisted pair Ethernet.  Never use solid core cable.

@@ Line 18: / Line 18: @@
 <tr>
 <td width=500>
-[[image:cablespec22_pinout.png]]  <br>
+[[image:ampmod_10pin_cable22.png|400px]]
 </td>
 <td>
-[[image:ampmod_10pin_cable22.png|400px]]
+[[image:cable22_ampmod_cableside.png|400px]]
 </td>
 </tr>
 </table>
 ==Other Pages==
 * Back to [[Cable Spec]]s

@@ Line 9: / Line 9: @@
 </td>
 <td>
-[[image:cablespec22_cableimage.png]]
+[[image:cablespec22_cableimage.png|400px]]
 </td>
 </tr>

@@ Line 21: / Line 21: @@
 </td>
 <td>
-[[image:ampmod_10pin_cable22.png|300px]]
+[[image:ampmod_10pin_cable22.png|400px]]
 </td>
 </tr>