CNC Bender v12.7 - Revision history

Mcone at 21:09, 1 February 2014

2014-02-01T21:09:25Z

2014-01-21T04:26:24Z

‎25px ENHANCED: Load and Start Positions with Bend Arm Motion Option (in Pre Bend)

2014-01-21T04:12:17Z

‎25px Other Changes

2014-01-21T04:11:17Z

‎25px Other Changes

2014-01-21T04:08:48Z

‎25px ENHANCED: Load and Start Positions with Bend Arm Motion

2014-01-21T04:08:06Z

‎25px ENHANCED: Post Bend Release Mode Has a New Mode

2014-01-21T04:07:58Z

‎25px ENHANCED: Load and Start Positions with Bend Arm Motion

2014-01-21T04:07:47Z

‎25px ENHANCED: PostBend Release Mode Has a New Mode

2014-01-21T04:07:00Z

‎25px ENHANCED: Extended Timing Control for Servo Modules

2014-01-21T04:04:32Z

‎25px ENHANCED: Loading with Bend Arm Motion

@@ Line 2: / Line 2: @@
 <tr>
 <td width=400>
-===v12.4 - January 20, 2014===
+===v12.7 - January 20, 2014===
 *Back to [[CNC Bender Software Updates]]
 *See [http://advancedtubular.com/customers/cncbender CNC Bender Customer Service Page] for an update.

@@ Line 34: / Line 34: @@
 : After Move to Start<br><br>
-Use this in conjunction with the PostBend Release command where you can turn off the bend arm return during release.</td>
+Use this in conjunction with the Post Bend Release command where you can turn off the bend arm return during release.</td>
 <td width=300>
 [[image:cncbender_ArmToHomeInPrebend.png|500px]]

@@ Line 64: / Line 64: @@
 <tr>
 <td width=400>
-* New COMDEFs were added to work with the new Arm To Home Mode above.  The commands are:
+* New COMDEFs were added to work with the new Arm To Home Mode option.  The commands are:
 </td>
 <td width=300>
 [[image:cncbender_armtohome_commands.png]]
 </td>
 </tr>

@@ Line 64: / Line 64: @@
 <tr>
 <td width=400>
-* The HAND BENDER MODE of CNC Bender is enhanced to allow for Bending without the Feed axis following.  This is helpful for applications where the last bend will pull the chuck into the pressure die or inside wiper die.
+* New COMDEFs were added to work with the new Arm To Home Mode above.  The commands are:
 </td>
 <td width=300>
 </td>
 </tr>

@@ Line 16: / Line 16: @@
 __NOTOC__
-==[[image:Check.jpg|25px]] ENHANCED: Load and Start Positions with Bend Arm Motion ==
+==[[image:Check.jpg|25px]] ENHANCED: Load and Start Positions with Bend Arm Motion Option (in Pre Bend)==
@@ Line 23: / Line 23: @@
 <tr>
 <td width=400>
-CNC Bender PreBend has a new option called "Arm to Home Mode" that controls when the bend arm returns home before bending begins.  The goal is optimization of the cycle.
+CNC Bender Pre Bend has a new option called "Arm to Home Mode" that controls when the bend arm returns home before bending begins.  The goal is optimization of the cycle.
 <br><br>
 These are the choices:<br><br>

@@ Line 52: / Line 52: @@
 </td>
 <td width=300>
-[[image:cncbender_autodieswithoutarm.png|300px]]
+[[image:cncbender_autodieswithoutarm.png|500px]]
 </td>
 <td>

@@ Line 43: / Line 43: @@
 </table><br><br>
-==[[image:Check.jpg|25px]] ENHANCED: PostBend Release Mode Has a New Mode ==
+==[[image:Check.jpg|25px]] ENHANCED: Post Bend Release Mode Has a New Mode ==
 <table>
@@ Line 52: / Line 52: @@
 </td>
 <td width=300>
-[[image:cncbender_autodieswithoutarm.jpg|300px]]
+[[image:cncbender_autodieswithoutarm.png|300px]]
 </td>
 <td>

← Older revision		Revision as of 04:04, 21 January 2014
Line 16:		Line 16:
	__NOTOC__		__NOTOC__

−	==[[image:Check.jpg\|25px]] ENHANCED: ~~Loading~~ with Bend Arm Motion ==	+	==[[image:Check.jpg\|25px]] ENHANCED: Load and Start Positions with Bend Arm Motion ==