CNC Bender v12.4 - Revision history

Mcone: /* 25px Other Changes */

2013-10-07T22:41:59Z

‎25px Other Changes

2013-10-05T16:31:22Z

‎25px ENHANCED: Benderlink

2013-10-05T16:30:08Z

‎25px ENHANCED: Benderlink

2013-10-05T16:29:48Z

‎25px ENHANCED: Benderlink

2013-10-05T16:29:30Z

‎25px ENHANCED: Benderlink

2013-10-05T16:26:02Z

‎25px ENHANCED: Benderlink

2013-10-05T16:25:50Z

‎25px ENHANCED: Benderlink

2013-10-05T16:25:37Z

‎25px ENHANCED: Benderlink

2013-10-05T16:25:10Z

‎25px Other Changes

2013-10-05T16:24:51Z

‎25px ENHANCED: Extended Timing Control for Servo Modules

@@ Line 59: / Line 59: @@
 <tr>
 <td width=400>
-* No other changes.
+* The HAND BENDER MODE of CNC Bender is enhanced to allow for Bending without the Feed axis following.  This is helpful for applications where the last bend will pull the chuck into the pressure die or inside wiper die.
 </td>
 <td width=300>

@@ Line 23: / Line 23: @@
 <tr>
 <td width=400>
-* DOCS software may send a changed rotation direction which could crash a bender during correction.<br><br>CNC Bender Benderlink intercepts this condition and automatically corrects the direction if rotatio data is already programmed into the control.   The problem especially occurs around the 180 degree rotation area.<br><br>This intercept and correction action is effective for when the measuring center sends data to both SVNET and Eaton Leonard benders.
+* DOCS software may send a changed rotation direction which could crash a bender during correction.<br><br>CNC Bender Benderlink intercepts this condition and automatically corrects the direction if rotatio data is already programmed into the control.   The problem especially occurs around the 180 degree rotation area.<br><br>This intercept and correction action is effective for any measuring center sending data to CNC Bender using either SVNET or Eaton Leonard Laservision protocols.
 <br>
 * The Compare Data tab is now the first one to display when entering Benderlink from Tube Shape.

@@ Line 23: / Line 23: @@
 <tr>
 <td width=400>
-* DOCS software may send a changed rotation direction which could crash a bender during correction.<br><br>CNC Bender Benderlink intercepts this condition and automatically corrects the direction if rotatio data is already programmed into the control.   The problem especially occurs around the 180 degree rotation area.<br><br>This intercept and correction is effective for when the measuring center sends data to both SVNET and Eaton Leonard benders.
+* DOCS software may send a changed rotation direction which could crash a bender during correction.<br><br>CNC Bender Benderlink intercepts this condition and automatically corrects the direction if rotatio data is already programmed into the control.   The problem especially occurs around the 180 degree rotation area.<br><br>This intercept and correction action is effective for when the measuring center sends data to both SVNET and Eaton Leonard benders.
 <br>
 * The Compare Data tab is now the first one to display when entering Benderlink from Tube Shape.

@@ Line 23: / Line 23: @@
 <tr>
 <td width=400>
-* DOCS software may send a changed rotation direction which could crash a bender during correction.<br><br>CNC Bender Benderlink intercepts this condition and automatically corrects the direction if rotatio data is already programmed into the control.   The problem especially occurs around the 180 degree rotation area.<br><br>This intercept and correcrtion is effective for when the measuring center sends data to both SVNET and Eaton Leonard benders.
+* DOCS software may send a changed rotation direction which could crash a bender during correction.<br><br>CNC Bender Benderlink intercepts this condition and automatically corrects the direction if rotatio data is already programmed into the control.   The problem especially occurs around the 180 degree rotation area.<br><br>This intercept and correction is effective for when the measuring center sends data to both SVNET and Eaton Leonard benders.
 <br>
 * The Compare Data tab is now the first one to display when entering Benderlink from Tube Shape.

@@ Line 23: / Line 23: @@
 <tr>
 <td width=400>
-* DOCS software may send a changed rotation direction which could crash a bender during correction.<br><br>CNC Bender Benderlink intercepts this condition and automatically corrects the direction if rotatio data is already programmed into the control.   The problem especially occurs around the 180 degree rotation area.
+* DOCS software may send a changed rotation direction which could crash a bender during correction.<br><br>CNC Bender Benderlink intercepts this condition and automatically corrects the direction if rotatio data is already programmed into the control.   The problem especially occurs around the 180 degree rotation area.<br><br>This intercept and correcrtion is effective for when the measuring center sends data to both SVNET and Eaton Leonard benders.
 <br>
 * The Compare Data tab is now the first one to display when entering Benderlink from Tube Shape.

@@ Line 43: / Line 43: @@
 <tr>
 <td width=400>
-The SMT operator stations now process data more quickly than in earlier modules.  This version of CNC Processor now more carefully governs the timing of all data sent to the servo modules.
+The SMT operator stations now process data more quickly than in earlier modules.  This version of CNC Processor now more carefully governs the timing of all data sent to the servo modules to prevent occasional TCP/IP errors due to CNC Bender outpacing the servo modules.
 <br><br>
 </td>