CNC Bender v12.2 - Revision history

Mcone: /* 25px ENHANCED: Output Diagnostic */

2013-09-27T20:03:21Z

‎25px ENHANCED: Output Diagnostic

2013-09-27T20:03:02Z

‎25px ENHANCED: Output Diagnostic

2013-09-26T22:12:40Z

‎25px ENHANCED: CIO Dictionary Editor Utility Added

2013-09-26T18:57:03Z

‎25px Other Changes

2013-09-26T18:56:44Z

‎25px Other Changes

2013-09-25T16:53:03Z

‎25px Other Changes

2013-09-25T16:52:49Z

‎25px Other Changes

2013-09-25T16:51:33Z

2013-09-25T16:50:49Z

‎25px NEW: Feed Adjust Percentage Warnings

2013-09-25T16:50:33Z

‎25px Other Changes

← Older revision		Revision as of 20:03, 27 September 2013
Line 65:		Line 65:


−	==[[image:Check.jpg\|25px]] ENHANCED: ~~Output Diagnostic~~ ==	+	==[[image:Check.jpg\|25px]] ENHANCED: Axis Speeds Menu ==

	The Axis Speeds setup menu in Low Level was redesigned so that the horizontal scroll bar is now visible on the screen.<br><br>		The Axis Speeds setup menu in Low Level was redesigned so that the horizontal scroll bar is now visible on the screen.<br><br>

@@ Line 60: / Line 60: @@
 * When an operator presses a point button, then the Set State button will toggle to the opposite state in anticipation that you intend to change it with the SET button.
 [[image:cncbender_outputdiagnostic.png|500px]]
 <br><br>

@@ Line 52: / Line 52: @@
 [[image:cncbender_ciodictionary_changemodulename.png|500px]]
 <br><br>
 ==[[image:Check.jpg|25px]] Other Changes ==

@@ Line 65: / Line 65: @@
 * Feed Distance Adjust percentages less than negative 100% will be reset to -100% automatically, because any lower value is not legal.
 <br>
-* If SKIP Run button feature is ON, and the Warning option is enabled (in low level), then CNC Bender will no longer put the bender in CYCLE HOLD when changing to AUTO mode.  The new action is a dialog will display on the screen with Continue or Stop options.  Pressing Continue will cause CNC Bender to move into AUTO mode with no further warnings.  Pressing STOP will put the bender back in the original mode (either MANUAL or STEP).
+* If SKIP Run button feature is ON, and the Warning option is enabled (in low level), then CNC Bender will no longer put the bender in CYCLE HOLD when changing to AUTO mode.  <br><br>The new action is a dialog will display on the screen with Continue or Stop options.  Pressing Continue will cause CNC Bender to move into AUTO mode with no further warnings.  Pressing STOP will put the bender back in the original mode (either MANUAL or STEP).
 </td>
 <td width=300>

@@ Line 64: / Line 64: @@
 <br>
 * Feed Distance Adjust percentages less than negative 100% will be reset to -100% automatically, because any lower value is not legal.
 </td>
 <td width=300>

@@ Line 69: / Line 69: @@
 </tr>
 </table>
 ==Other Pages==

← Older revision		Revision as of 16:50, 25 September 2013
Line 45:		Line 45:

	[[image:cncbender_warning_50percent_feeddistanceadjust.png\|600px]]		[[image:cncbender_warning_50percent_feeddistanceadjust.png\|600px]]
		+	<br><br>

	==[[image:Check.jpg\|25px]] ENHANCED: CIO Dictionary Editor Utility Added ==		==[[image:Check.jpg\|25px]] ENHANCED: CIO Dictionary Editor Utility Added ==

@@ Line 58: / Line 58: @@
 <br>
 * Manual page Absolute feed moves will now swing away the inside wiper when moving inside the inside wiper zone.
 ==Other Pages==