CNC Bender v12-20130723 - Revision history

Mcone at 12:25, 24 July 2013

2013-07-24T12:25:32Z

Mcone: /* 25px Other Changes */

2013-07-23T22:46:12Z

‎25px Other Changes

Mcone: /* 25px Other Changes */

2013-07-23T22:45:39Z

‎25px Other Changes

Mcone: /* 25px NEW: Any Command (COMDEF) can be taught to ignore Cycle Hold */

2013-07-23T22:45:17Z

‎25px NEW: Any Command (COMDEF) can be taught to ignore Cycle Hold

Mcone: /* 25px NEW: Any Command (COMDEF) can be taught to ignore Cycle Hold */

2013-07-23T22:44:39Z

‎25px NEW: Any Command (COMDEF) can be taught to ignore Cycle Hold

Mcone: /* 25px NEW: Any Command (COMDEF) can be taught to ignore Cycle Hold */

2013-07-23T22:43:52Z

‎25px NEW: Any Command (COMDEF) can be taught to ignore Cycle Hold

Mcone: /* 25px NEW: Any Command (COMDEF) can be taught to ignore Cycle Hold */

2013-07-23T22:43:12Z

‎25px NEW: Any Command (COMDEF) can be taught to ignore Cycle Hold

Mcone: /* 25px Other Changes */

2013-07-23T22:36:50Z

‎25px Other Changes

Mcone: /* v12-20130722 */

2013-07-23T22:30:41Z

‎v12-20130722

Mcone: /* 25px NEW: Any Command (COMDEF) can be taught to ignore Cycle Hold */

2013-07-23T22:28:52Z

‎25px NEW: Any Command (COMDEF) can be taught to ignore Cycle Hold

@@ Line 15: / Line 15: @@
 __NOTOC__
-See [http://advancedtubular.com/customers/cncbender/page-downloads/v12-20130722.html CNC Bender Customer Service Page] for an update.
+See [http://advancedtubular.com/customers/cncbender/page-downloads/v12-20130723.html CNC Bender Customer Service Page] for an update.
 ===[[image:Check.jpg|25px]] NEW: Any Command (COMDEF) can be taught to ignore Cycle Hold ===

@@ Line 54: / Line 54: @@
 * This version of CNC Bender has a decreased input check time from 125 ms to 16 ms for faster response time.<br><br>
 * This version has repaired logic issue with BEGIN condition inputs that would cause Commands to show incompleted inputs when they were completed.<br><br>
-* This version has repaired logic issue edge detection for inputs.<br><br>
+* This version has repaired logic for an issue with edge-detection for inputs.<br><br>
 * This version allows the input for Master Power ON to be either a BEGIN or END style input without causing the bender to to never drop out of AUTO mode.<br><br>
 * The version allows the Safety Relay ON to be either a BEGIN or END style input without a causing the bender to never drop out of AUTO mode.<br><br>

@@ Line 54: / Line 54: @@
 * This version of CNC Bender has a decreased input check time from 125 ms to 16 ms for faster response time.<br><br>
 * This version has repaired logic issue with BEGIN condition inputs that would cause Commands to show incompleted inputs when they were completed.<br><br>
-* This version has repaired logic issue edge detection for inputs.
+* This version has repaired logic issue edge detection for inputs.<br><br>
 * This version allows the input for Master Power ON to be either a BEGIN or END style input without causing the bender to to never drop out of AUTO mode.<br><br>
 * The version allows the Safety Relay ON to be either a BEGIN or END style input without a causing the bender to never drop out of AUTO mode.<br><br>

@@ Line 24: / Line 24: @@
 For example, the Allen Bradley 800Z Zero Force Touch Buttons can be installed on the left and right side of control.<br><br>
 With manual unloading, there are points in the cycle where it is necessary to grasp the part and open the dies to remove the part from the bender.  However, removing hands from the touch buttons to remove the part puts the part into CYCLE HOLD.  The commands that examine the RELEASE button and open the dies can be programmed to ignore CYCLE HOLD in order to open the dies in CYCLE HOLD.<br><br>
-Another benefit of this capability is that commands that wait and watch, illuminate buttons/indicator lights, or set outputs without moving actuators can be working even during CYCLE HOLD.  This speeds the process by letting the non-motion commands to continue to run.
+Another benefit of this capability is that commands that wait and watch, illuminate buttons/lights, or set outputs without moving actuators can be working even during CYCLE HOLD.  This speeds the process by letting the non-motion commands to continue to run even in CYCLE HOLD.
 </td>

@@ Line 24: / Line 24: @@
 For example, the Allen Bradley 800Z Zero Force Touch Buttons can be installed on the left and right side of control.<br><br>
 With manual unloading, there are points in the cycle where it is necessary to grasp the part and open the dies to remove the part from the bender.  However, removing hands from the touch buttons to remove the part puts the part into CYCLE HOLD.  The commands that examine the RELEASE button and open the dies can be programmed to ignore CYCLE HOLD in order to open the dies in CYCLE HOLD.<br><br>
-Another benefit of this capability is that commands that wait and watch, illuminate buttons and indicators, or set outputs without moving actuators can be working even during CYCLE HOLD.  This speeds the process by letting the non-motion commands to continue to run.
+Another benefit of this capability is that commands that wait and watch, illuminate buttons/indicator lights, or set outputs without moving actuators can be working even during CYCLE HOLD.  This speeds the process by letting the non-motion commands to continue to run.
 </td>

@@ Line 23: / Line 23: @@
 This new feature allows selected COMDEFs to run in the processlist without pausing during CYCLE HOLD.  The reason for this new capability is that some customers require that their benders be equipped with palm buttons that must be held during any part of the bending with pinch-point motion.<br><br>
 For example, the Allen Bradley 800Z Zero Force Touch Buttons can be installed on the left and right side of control.<br><br>
-There are points in the cycle where it is necessary to grasp the part and open the dies to remove the part from the bender.  However, removing hands from the touch buttons to remove the part puts the part into cycle hold.  The commands that examine the RELEASE button and open the dies can be programmed to ignore CYCLE HOLD in order to open the dies in CYCLE HOLD.<br><br>
+With this configuration, there are points in the cycle where it is necessary to grasp the part and open the dies to remove the part from the bender.  However, removing hands from the touch buttons to remove the part puts the part into cycle hold.  The commands that examine the RELEASE button and open the dies can be programmed to ignore CYCLE HOLD in order to open the dies in CYCLE HOLD.<br><br>
 Another benefit of this capability is that commands that wait and watch, illuminate buttons and indicators, or set outputs without moving actuators can be working even during CYCLE HOLD.  This speeds the process by letting the non-motion commands to continue to run.

@@ Line 2: / Line 2: @@
 <tr>
 <td width=200>
-==v12-20130722==
+==v12-20130723==
 *Back to [[CNC Bender Software Updates]]