CNC Bender v12-20120622 - Revision history

Mcone: /* 25px Enhancement - AutoSleep Removed */

2012-06-30T01:31:45Z

‎25px Enhancement - AutoSleep Removed

Mcone: /* 25px Repair - Robot Clear Bit Can Be High or Low */

2012-06-30T01:31:18Z

‎25px Repair - Robot Clear Bit Can Be High or Low

Mcone at 01:17, 30 June 2012

2012-06-30T01:17:49Z

Mcone: /* 25px New - Radius Level for LOAD Position in PREBEND */

2012-06-30T01:17:03Z

‎25px New - Radius Level for LOAD Position in PREBEND

Mcone: /* 25px New - Radius Level for LOAD Position in PREBEND */

2012-06-30T01:16:35Z

‎25px New - Radius Level for LOAD Position in PREBEND

Mcone: /* 25px New - Horizontal Axis LOAD Position in PREBEND */

2012-06-30T01:05:33Z

‎25px New - Horizontal Axis LOAD Position in PREBEND

Mcone: /* 25px New - Radius Level for LOAD Position in PREBEND */

2012-06-30T00:57:39Z

‎25px New - Radius Level for LOAD Position in PREBEND

Mcone: /* 25px New - Radius Level for LOAD Position in PREBEND */

2012-06-30T00:53:19Z

‎25px New - Radius Level for LOAD Position in PREBEND

Mcone: /* 25px Repair - Robot Clear Bit Can Be High or Low */

2012-06-30T00:53:01Z

‎25px Repair - Robot Clear Bit Can Be High or Low

Mcone at 00:35, 30 June 2012

2012-06-30T00:35:35Z

@@ Line 94: / Line 94: @@
 Since CNC Processor is now highly optimized, the AutoSleep feature, where the CNC Bender user interface could be put to sleep to decrease delay between steps, is no longer needed.<br>
 <br>
-Now the bender runs fast with our without AutoSleep enabled.
+Now the CNC Processor runs fast with our without AutoSleep enabled.
 </td>

← Older revision		Revision as of 01:31, 30 June 2012
Line 87:		Line 87:
	</table>		</table>

		+	===[[image:Check.jpg\|25px]] Enhancement - AutoSleep Removed===

		+	<table cellpadding=10>
		+	<tr valign=top>
		+	<td width=400>
		+	Since CNC Processor is now highly optimized, the AutoSleep feature, where the CNC Bender user interface could be put to sleep to decrease delay between steps, is no longer needed.<br>
		+	<br>
		+	Now the bender runs fast with our without AutoSleep enabled.
		+	</td>
		+
		+	<td width=300>
		+
		+	</td>
		+
		+	</tr>
		+	</table>

	=Other Pages=		=Other Pages=

@@ Line 13: / Line 13: @@
 </table>
 __NOTOC__
-===[[image:Check.jpg|25px]] Repair - Recovery Mode Rotate Spin 180===
 <table cellpadding=10>
 <tr valign=top>
 <td width=400>
-The ROTATE axis could incorrectly rotate 360 degrees when recovering from safety mat activation under rare circumstances of the rotate drifting way from zero.  This has been fixed.
+The new option "Radius Level for Loading" shows a list composed of 5 options for controlling where the carriage is vertically during LOADING the part.   These are the five options:<br>
 <br>
 </td>
@@ Line 29: / Line 37: @@
 </table>
-===[[image:Check.jpg|25px]] Repair - Robot Clear Bit Can Be High or Low===
+===[[image:Check.jpg|25px]] New - Horizontal Axis LOAD Position in PREBEND===
 <table cellpadding=10>
 <tr valign=top>
 <td width=400>
-The Robot Clear bit always assumed that the TRUE signal was bit high.  But some machines assume the opposite.  This has been fixed.
+A new option allows the horizontal axis to move to a specific position for loading.  This is a two-option feature:<br>
 <br>
 </td>
 <td width=300>
 </td>
 </tr>
 </table>
+===[[image:Check.jpg|25px]] Repair - Recovery Mode Rotate Spin 180===
-===[[image:Check.jpg|25px]] New - Radius Level for LOAD Position in PREBEND===
 <table cellpadding=10>
 <tr valign=top>
 <td width=400>
-The new option "Radius Level for Loading" shows a list composed of 5 options for controlling where the carriage is vertically during LOADING the part.   These are the five options:<br>
+The ROTATE axis could incorrectly rotate 360 degrees when recovering from safety mat activation under rare circumstances of the rotate drifting way from zero.  This has been fixed.
 <br>
 </td>
@@ Line 69: / Line 70: @@
 </table>
-===[[image:Check.jpg|25px]] New - Horizontal Axis LOAD Position in PREBEND===
+===[[image:Check.jpg|25px]] Repair - Robot Clear Bit Can Be High or Low===
 <table cellpadding=10>
 <tr valign=top>
 <td width=400>
-A new option allows the horizontal axis to move to a specific position for loading.  This is a two-option feature:<br>
+The Robot Clear bit always assumed that the TRUE signal was bit high.  But some machines assume the opposite.  This has been fixed.
 </td>
 <td width=300>
 </td>
 </tr>
 </table>
-[[image:cncbender_horizontalaxisloadposition.jpg]]
 =Other Pages=

@@ Line 69: / Line 69: @@
 </table>
-[[image:cncbender_radiuslevel_for_loading.jpg|200px]]
+[[image:cncbender_radiuslevel_for_loading.jpg]]
 ===[[image:Check.jpg|25px]] New - Horizontal Axis LOAD Position in PREBEND===

← Older revision		Revision as of 01:16, 30 June 2012
Line 69:		Line 69:
	</table>		</table>

		+	[[image:cncbender_radiuslevel_for_loading.jpg\|200px]]

	===[[image:Check.jpg\|25px]] New - Horizontal Axis LOAD Position in PREBEND===		===[[image:Check.jpg\|25px]] New - Horizontal Axis LOAD Position in PREBEND===

@@ Line 2: / Line 2: @@
 <tr>
 <td width=200>
-==v12-20111229==
+==v12-20120622==
 *Back to [[CNC Bender Software Updates]]
 </td>