CNC Bender v12-20110128 - Revision history

Mcone: /* 25px ENHANCED - AUTO MODE can now Always be STEP MODE */

2011-01-28T23:00:54Z

‎25px ENHANCED - AUTO MODE can now Always be STEP MODE

Mcone: /* 25px ENHANCED - Teach Mode Button Can Be Invisible */

2011-01-28T23:00:10Z

‎25px ENHANCED - Teach Mode Button Can Be Invisible

Mcone: /* 25px ENHANCED - Teach Mode Button Can Be Invisible */

2011-01-28T22:54:32Z

‎25px ENHANCED - Teach Mode Button Can Be Invisible

Mcone: /* 25px ENHANCED - Teach Mode Button Can Be Invisible */

2011-01-28T22:48:15Z

‎25px ENHANCED - Teach Mode Button Can Be Invisible

Mcone: /* 25px ENHANCED - Teach Mode Button Can Be Invisible */

2011-01-28T22:47:38Z

‎25px ENHANCED - Teach Mode Button Can Be Invisible

Mcone: /* 25px ENHANCED - Teach Mode Button Can Be Invisible */

2011-01-28T22:45:27Z

‎25px ENHANCED - Teach Mode Button Can Be Invisible

Mcone: /* 25px ENHANCED - Empty Process Lists Now Allowed */

2011-01-28T22:45:19Z

‎25px ENHANCED - Empty Process Lists Now Allowed

Mcone: /* 25px NEW - Process List Commands Can Ignore STEP Mode */

2011-01-28T22:39:39Z

‎25px NEW - Process List Commands Can Ignore STEP Mode

Mcone at 22:38, 28 January 2011

2011-01-28T22:38:42Z

New page

<table>
<tr>
<td width=200>
==v12-20110128==
*Back to [[CNC Bender Software Updates]]
</td>
<td width=300>
[[image:cncv12procontrol_withteachmode.jpg|300px]]<br>
</td>
<td>
</td>
</tr>
</table>

__NOTOC__
===[[image:Check.jpg|25px]] NEW - Process List Commands Can Ignore STEP Mode ===

<table cellpadding=10>
<tr valign=top>
<td width=300>
Some commands don't move the actuators on bender. They only setup the bender. Now these commands can be told to not PAUSE during STEP MODE. This will reduce the number of run-button or foot-pedal steps required to run through a part on the bender in STEP mode.
<br><br>
The COMDEF Editor has a new "Ignore STEP Mode" checkbox for each COMMAND.
</td>
<td>
[[image:comdefeditor_ignorestepmode.jpg|300px]]
</td>
</tr>
</table>

===[[image:Check.jpg|25px]] ENHANCED - Empty Process Lists Now Allowed ===

<table cellpadding=10>
<tr valign=top>
<td width=300>
Empty process lists are now allowed in CNC Bender.
</td>
</tr>
</table>
<br><br>

=Other Pages=
*Back to [[CNC Bender]]
*Back to [[CNC Bender Software Updates]]
*See [[CNC Bender General Information]]
*See [[Teach Mode]]
*See [[Custom Command]]s

@@ Line 55: / Line 55: @@
 <tr valign=top>
 <td width=300>
-For controlled benders that are hand-powered, it is always appropriate to
+For controlled benders that are hand-powered, it is always appropriate to run in STEP mode rather than AUTO mode.  If this option is enabled, then AUTO mode always runs in STEP mode.
 <br>
 [[image:alwaysruninstepmode_option.jpg|400px]]

@@ Line 36: / Line 36: @@
 Some benders don't need TEACH Mode, so the Teach Mode button can be made invisible by enabling a switch in the low level options list.
 <br>
-[[image:teachbuttoninvisible_button.jpg]]
+[[image:teachbuttoninvisible_option.jpg|400px]]
 </td>
 <td>
-[[image:teachbuttoninvisible_option.jpg|400px]]
+[[image:teachbuttoninvisible_button.jpg]]
 </td>

@@ Line 35: / Line 35: @@
 <td width=300>
 Some benders don't need TEACH Mode, so the Teach Mode button can be made invisible by enabling a switch in the low level options list.
 </td>

@@ Line 38: / Line 38: @@
 <td>
-[image:teachbuttoninvisible_option.jpg|400px]]
+[[image:teachbuttoninvisible_option.jpg|400px]]
 </td>

← Older revision		Revision as of 23:00, 28 January 2011
Line 48:		Line 48:
	<br><br>		<br><br>

		+
		+
		+	===[[image:Check.jpg\|25px]] ENHANCED - AUTO MODE can now Always be STEP MODE ===
		+
		+	<table cellpadding=10>
		+	<tr valign=top>
		+	<td width=300>
		+	For controlled benders that are hand-powered, it is always appropriate to
		+	<br>
		+	[[image:alwaysruninstepmode_option.jpg\|400px]]
		+	</td>
		+
		+	<td>
		+
		+	</td>
		+
		+	</tr>
		+	</table>
		+	<br><br>

	===[[image:Check.jpg\|25px]] ENHANCED - Output Diagnostic ===		===[[image:Check.jpg\|25px]] ENHANCED - Output Diagnostic ===

@@ Line 29: / Line 29: @@
 </table>
-===[[image:Check.jpg|25px]] ENHANCED - Empty Process Lists Now Allowed  ===
+===[[image:Check.jpg|25px]] ENHANCED - Teach Mode Button Can Be Invisible  ===
 <table cellpadding=10>
 <tr valign=top>
 <td width=300>
-Empty process lists are now allowed in CNC Bender.
+Some benders don't need TEACH Mode, so the Teach Mode button can be made invisible by enabling a switch in the low level options list.
 </td>
 </tr>
 </table>

@@ Line 24: / Line 24: @@
 </td>
 <td>
-[[image:comdefeditor_ignorestepmode.jpg|300px]]
+[[image:comdefeditor_ignorestepmode.jpg|400px]]
 </td>
 </tr>