CNC Bender v12-20101102 - Revision history

Mcone: /* 25px NEW - Separate Timer in CNC Processor for Direct Axis Jog Input Detection */

2010-11-04T14:08:49Z

‎25px NEW - Separate Timer in CNC Processor for Direct Axis Jog Input Detection

2010-11-04T14:08:26Z

‎25px NEW - Separate Timer in CNC Processor for Direct Axis Jog Input Detection

2010-11-04T14:06:33Z

‎25px NEW - Separate Timer in CNC Processor for Teach Pendant Input Detection

2010-11-04T14:06:06Z

‎25px NEW - Separate Timer in CNC Processor for Teach Pendant Input Detection

2010-11-04T14:05:30Z

‎25px NEW - Separate Timer for Teach Pendant Input Detection

2010-11-04T14:04:00Z

‎25px NEW - Separate Timer for Teach Pendant Motion

2010-11-04T14:03:20Z

‎25px NEW - Default Jog Speed in Axislist Configuration

2010-11-04T02:59:46Z

‎25px NEW - Dedicated Timer in CNC Processor for Teach Pendant Jog

2010-11-04T02:38:22Z

‎25px NEW - Dedicated Timer in CNC Processor for Teach Pendant Jog

2010-11-04T02:38:07Z

‎25px NEW - Dedicated Timer in CNC Processor for Pendant Teach Jog

← Older revision		Revision as of 14:08, 4 November 2010
Line 109:		Line 109:

	</table>		</table>
		+
		+	<br><br>

	===[[image:Check.jpg\|25px]] REMOVE - SetDefaultJogSpeeds In Init Axis Process ===		===[[image:Check.jpg\|25px]] REMOVE - SetDefaultJogSpeeds In Init Axis Process ===

@@ Line 102: / Line 102: @@
 </td>
 <td width=400>
-A new set of properties is found inside the CNCProcessor.cfg file in the c:\cnc\config folder:
+A new set of properties is found inside the CNCProcessor.cfg file in the c:\cnc\config folder. See the two new properties at the bottom of this screen image:
-<br><br>
-See the screen image below for the new properties in CNCProcessor.cfg file.<br><br>
 [[image:direct_axis_jog_properties.jpg]]

← Older revision		Revision as of 14:06, 4 November 2010
Line 89:		Line 89:


−	===[[image:Check.jpg\|25px]] NEW - Separate Timer in CNC Processor for ~~Teach Pendant~~ Input Detection ===	+	===[[image:Check.jpg\|25px]] NEW - Separate Timer in CNC Processor for Direct Axis Jog Input Detection ===

	<table cellpadding=10>		<table cellpadding=10>

@@ Line 96: / Line 96: @@
 CNC Processor has a new dedicated timer for detecting +/- inputs for direct axes jogs.  This carefully regulates the timing of the jog commands being sent to the servo modules.
 <br><br>
 Setup:
@@ Line 106: / Line 102: @@
 </td>
 <td width=400>
 [[image:direct_axis_jog_properties.jpg]]
 </td>

@@ Line 89: / Line 89: @@
-===[[image:Check.jpg|25px]] NEW - Separate Timer for Teach Pendant Input Detection  ===
+===[[image:Check.jpg|25px]] NEW - Separate Timer in CNC Processor for Teach Pendant Input Detection  ===
 <table cellpadding=10>
 <tr valign=top>
 <td width=200>
-CNC Bender has a new dedicated timer for the direct axes jogs inside CNC Processor.
+CNC Processor has a new dedicated timer for detecting +/- inputs for direct axes jogs.  This carefully regulates the timing of the jog commands being sent to the servo modules.
 <br><br>

@@ Line 82: / Line 82: @@
 *If a default jog speed is negative, it is reset to the positive value.
 *If a default jog speed exceeds the maximum speed for an axis, then it is reset to the maximum speed.
 </td>
 </tr>

@@ Line 43: / Line 43: @@
 </table>
-===[[image:Check.jpg|25px]] NEW - Dedicated Timer in CNC Processor for Teach Pendant Jog  ===
+===[[image:Check.jpg|25px]] NEW - Dedicated Timer in CNC Processor for [[Teach Pendant]] Jog  ===
 <table cellpadding=10>