CNC Bender v12-20100414 - Revision history

Mcone: /* 25px REPAIRED - Automatic Feed Adjustment During Part Load */

2010-04-16T14:28:38Z

‎25px REPAIRED - Automatic Feed Adjustment During Part Load

2010-04-16T14:22:38Z

‎25px REPAIRED - Automatic Feed Adjustment Fix

2010-04-16T14:22:13Z

‎25px ENHANCED - Benderlink Changes START Position Adjustment

2010-04-16T14:21:58Z

‎25px REPAIRED - Direct Axes Jog Buttons Stick Down

2010-04-16T14:04:34Z

‎25px REPAIRED - Direct Axes Jog Buttons Stick Down

2010-04-16T14:02:14Z

‎25px REPAIRED - Benderlink Database Transfer Setup Clear

2010-04-15T02:42:32Z

‎25px REPAIRED - Benderlink Database Transfer Setup Clear

2010-04-15T02:41:56Z

‎25px REPAIRED - Benderlink Database Transfer

2010-04-15T02:41:25Z

2010-04-15T02:41:00Z

@@ Line 97: / Line 97: @@
 <tr valign=top>
 <td width=300>
-The automatic feed adjustment feature works by advising operators that incoming part data was from another bender with a different bed length.  We discovered and solved problems with a couple of options in the Tool page.</td>
+The automatic feed adjustment feature works by advising operators that incoming part data was from another bender with a different bed length.  We discovered that two of the Tool page options were not being changed properly.  This is corrected.</td>
 <td>
 </td>

@@ Line 93: / Line 93: @@
 </table>
-===[[image:Check.jpg|25px]] REPAIRED - Automatic Feed Adjustment Fix===
+===[[image:Check.jpg|25px]] REPAIRED - Automatic Feed Adjustment During Part Load===
 <table>
 <tr valign=top>

@@ Line 30: / Line 30: @@
 <td width=300>
 </td>
 <td>
 </td>
 </tr>
 </table>
 ===[[image:Check.jpg|25px]] REPAIRED - Benderlink Database Transfer Setup Clear===

@@ Line 94: / Line 94: @@
 </td>
 </tr>
 </table>
 ===[[image:Check.jpg|25px]] REPAIRED - Automatic Feed Adjustment Fix===

@@ Line 84: / Line 84: @@
 If the Immediate Message box displays while an operator is pressing a JOG+ or JOG- button in direct axes jog mode, then CNC Bender would never allow the jog button to come up.  This has been resolved.
 </td>
 <td>
 </td>

← Older revision		Revision as of 14:02, 16 April 2010
Line 15:		Line 15:

	__TOC__		__TOC__
		+
		+
		+	===[[image:Check.jpg\|25px]] ENHANCED - Benderlink Changes START Position Adjustment===
		+	<table>
		+	<tr valign=top>
		+	<td width=300>
		+	Benderlink is enhanced to correctly change the START position of the carriage during correction if that feature is switched on.
		+	</td>
		+	<td>
		+	</td>
		+	</tr>
		+
		+	<tr valign=top>
		+	<td width=300>
		+	</td>
		+
		+	<td>
		+	</td>
		+	</tr>
		+
		+	</table>

@@ Line 22: / Line 22: @@
 <td width=300>
 The CNC Bender database was corrupted when Benderlink users pressed the "Apply and Close" button without first having made a correction.  The result was a CNC Bender setup that would cause major issues in CNC Bender.<br><br>
-This issue has been corrected by automatically updating the Adjusted database when Benderlink shows on the screen.  There is no possibility that the the setup database can now be cleared;
+This issue has been corrected by automatically updating the Adjusted database when Benderlink shows on the screen.  There is no possibility that the the setup database can now be cleared improperly.
 </td>
 <td>

@@ Line 5: / Line 5: @@
 <br>
-<table>
-<tr>
-<td>
-Upgrade Involves: Benderlink
-</td>
-<td>
-</td>
-</tr>
-</table>
 </td>

@@ Line 11: / Line 11: @@
 </td>
 <td>
 </td>
 </tr>