CNC Bender v12-20100324 - Revision history

Mcone: /* 25px ENHANCE- Rotation Recovery Shortest Angle Possible */

2010-03-25T16:59:22Z

‎25px ENHANCE- Rotation Recovery Shortest Angle Possible

2010-03-25T16:56:39Z

‎25px ENHANCE- Rotation Recovery Shortest Angle Possible

2010-03-25T16:55:37Z

2010-03-25T16:55:07Z

2010-03-25T16:54:13Z

2010-03-25T16:51:36Z

2010-03-24T20:06:16Z

‎25px ADDED - Cycle Hold Last Bend After Dies Open

2010-03-24T20:06:01Z

‎25px ADDED - Cycle Hold After Dies Open in Post Bend

2010-03-24T20:03:55Z

‎25px ADDED - Cycle Hold After Dies Open in Post Bend

2010-03-24T20:03:06Z

‎25px ADDED - Cycle Hold After Dies Open in Post Bend

@@ Line 26: / Line 26: @@
-===[[image:Check.jpg|25px]] ENHANCE- Rotation Recovery Shortest Angle Possible===
+===[[image:Check.jpg|25px]] ENHANCED- Rotation Recovery Shortest Angle Possible===
 <table>
 <tr valign=top>

@@ Line 37: / Line 37: @@
 </td>
 </tr>
 <tr valign=top>
@@ Line 48: / Line 47: @@
 </table>
 ===[[image:Check.jpg|25px]] DEBUG - Machine Lube Timer Logic===

@@ Line 8: / Line 8: @@
 <tr>
 <td>
-Type of Upgrade: Significant Upgrade
+Type of Upgrade: Minor Upgrade
 </td>
 <td>
-Recovery Rotate Logic
+Recovery Rotate Logic Enhancement
 </td>
 </tr>

@@ Line 26: / Line 26: @@
-===[[image:Check.jpg|25px]] FIX - Rotation Recovery Logic===
+===[[image:Check.jpg|25px]] ENHANCE- Rotation Recovery Shortest Angle Possible===
 <table>
 <tr valign=top>
 <td width=300>
-When a rotation is stopped and recovered by stepping on the safety mat, the rotation direction would not always move the shortest distance and direction to recover.
+When a rotation is stopped and recovered by stepping on the safety mat, the rotation direction would not always move the shortest angle and direction to recover.
 <br><br>
-This has been resolved so that all non-linear axes recover in the direction that is measured as the shortest possible.
+This has been resolved so that all non-linear axes recover in the direction that is measured as the shortest possible angle.
 </td>
 <td>

← Older revision		Revision as of 16:54, 25 March 2010
Line 24:		Line 24:

	__TOC__		__TOC__
		+
		+
		+	===[[image:Check.jpg\|25px]] FIX - Rotation Recovery Logic===
		+	<table>
		+	<tr valign=top>
		+	<td width=300>
		+	When a rotation is stopped and recovered by stepping on the safety mat, the rotation direction would not always move the shortest distance and direction to recover.
		+	<br><br>
		+	This has been resolved so that all non-linear axes recover in the direction that is measured as the shortest possible.
		+	</td>
		+	<td>
		+	</td>
		+	</tr>
		+
		+
		+	<tr valign=top>
		+	<td width=300>
		+	</td>
		+
		+	<td>
		+	</td>
		+	</tr>
		+
		+	</table>
		+
		+

	===[[image:Check.jpg\|25px]] DEBUG - Machine Lube Timer Logic===		===[[image:Check.jpg\|25px]] DEBUG - Machine Lube Timer Logic===

@@ Line 48: / Line 48: @@
 </table>
-===[[image:Check.jpg|25px]] ADDED - Cycle Hold Last Bend After Dies Open===
+===[[image:Check.jpg|25px]] ADDED - Cycle Hold After Last Bend After Dies Open===
 <table>
 <tr valign=top>

@@ Line 54: / Line 54: @@
 This feature was requested so we added it to CNC Bender.
 <br><br>
-Now the process list will go into cycle hold after the dies open if this option is switched ON in the last bend cell (part release) section.
+Now the bender will go into cycle hold after the last bend after the dies open if this option is switched ON in the last bend cell (part release) section.
 </td>
 <td>