CNC Bender v11-20090120 - Revision history

Mcone: /* 25px REPAIR - Motion Recovery Logic Fix */

2009-04-06T14:08:11Z

‎25px REPAIR - Motion Recovery Logic Fix

2009-01-21T12:50:01Z

‎25px NEW - Internal Binary Register I/O Feature

2009-01-21T12:49:35Z

‎25px NEW - Internal Binary Register I/O Feature

2009-01-21T12:47:45Z

‎25px REPAIR - Motion Recovery Logic

2009-01-21T12:47:32Z

‎25px NEW - Internal Binary Register I/O Feature

2009-01-21T12:47:17Z

‎25px NEW - Multitask Process List RESET Feature

2009-01-21T12:47:06Z

‎25px NEW - Multitask Process List RESET Feature

2009-01-21T12:46:44Z

‎25px NEW - Multitask Process List RESET Feature

2009-01-21T12:43:40Z

‎25px REPAIR - Motion Recovery Logic

2009-01-21T12:42:59Z

‎25px REPAIR - Motion Recovery Logic

@@ Line 40: / Line 40: @@
 The motion recovery logic was adjusted so that:
 <br>
-# It will run only for COMDEF commands that actually have axis motion logic in them.  (Many commands handle only inputs or outputs.
+# It will run only for COMDEF commands that actually have axis motion logic in them.  (Many commands handle only inputs or outputs.)
 # It will run in secondary process lists only if the list is running when SAFE MODE CYCLE HOLD was activated.  Secondary processes that are not running need to have no recovery motion applied to them.
 <br><br>

@@ Line 31: / Line 31: @@
 Internal Binary Registers can treat the same point in the same module as both OUTPUT and INPUT at the same time in the same module.   (This is not possible in CIO objects linked to physical modules.)
 <br><br>
-This gives the advantage of being able to set an IBR output in one process while examining the same IBR as an input in another process.
+This gives the advantage of being able to set an IBR OUTPUT in one process while examining the same IBR as an INPUT in another process.
 <br><br>

@@ Line 30: / Line 30: @@
 <br><br>
 Internal Binary Registers can treat the same point in the same module as both OUTPUT and INPUT at the same time in the same module.   (This is not possible in CIO objects linked to physical modules.)
 <br><br>

@@ Line 32: / Line 32: @@
 <br><br>
-===[[image:Check.jpg|25px]] REPAIR - Motion Recovery Logic===
+===[[image:Check.jpg|25px]] REPAIR - Motion Recovery Logic Fix===
 Motion recovery allows a user to step into the safety scanner during the middle of a motion command, stop all motion, then allow CNC Bender to finish the motion automatically after cycle start is pressed.

@@ Line 31: / Line 31: @@
 Internal Binary Registers can treat the same point in the same module as both OUTPUT and INPUT at the same time in the same module.   (This is not possible in CIO objects linked to physical modules.)
 <br><br>
 ===[[image:Check.jpg|25px]] REPAIR - Motion Recovery Logic===

@@ Line 22: / Line 22: @@
 <br><br>
 The RESET command solves issues that may crop up when starting a secondary process inadvertently in the middle of the list.  For example, if the process list is running in CONTINUE mode (the old default), then the process could accidentally automatically close the chuck at the beginning of a new cycle.
 <br>

← Older revision		Revision as of 12:46, 21 January 2009
Line 25:		Line 25:
	<br><br>		<br><br>

		+
		+	===[[image:Check.jpg\|25px]] NEW - Internal Binary Register I/O Feature===
		+
		+	CNC Bender uses Internal Binary Registers to simulate input or output modules
		+	<br><br>
		+	Internal Binary Registers can treat the same point in the same module as both OUTPUT and INPUT at the same time in the same module. (This is not possible in CIO objects linked to physical modules.)
		+	<br><br>
		+
		+	An example for starting a secondary processes is shown here. The new RESET parameter is at the end of the line following the ENABLE command:

	===[[image:Check.jpg\|25px]] REPAIR - Motion Recovery Logic===		===[[image:Check.jpg\|25px]] REPAIR - Motion Recovery Logic===