CNC Bender v11-20081230 - Revision history

Mcone: /* 25px NEW - Push Bend Twist GEARING - Accurate Helical Coils */

2009-01-02T04:09:28Z

‎25px NEW - Push Bend Twist GEARING - Accurate Helical Coils

2009-01-02T04:09:15Z

‎25px NEW - Push Bend Twist GEARING

2009-01-02T03:40:27Z

‎25px NEW - Calculate TOTAL BEND ANGLE for a Push Bend Coil

2009-01-02T03:09:29Z

‎25px NEW - Push Bend Twist GEARING

2009-01-02T02:59:15Z

‎25px NEW - Push Bend Twist GEARING

2009-01-02T02:57:33Z

‎25px NEW - Calculate TOTAL BEND ANGLE for a Push Bend Coil

2009-01-02T02:57:19Z

‎25px NEW - Calculate TOTAL BEND ANGLE for a Push Bend Coil

2009-01-02T02:56:48Z

‎25px NEW - Calculate TOTAL BEND ANGLE for a Push Bend Coil

2009-01-02T02:56:31Z

‎25px NEW - Calculate TOTAL BEND ANGLE for a Push Bend Coil

2009-01-02T02:56:05Z

‎25px NEW - Calculate TOTAL BEND ANGLE for a Push Bend Coil

@@ Line 14: / Line 14: @@
 <br><br>
-===[[image:Check.jpg|25px]] NEW - Push Bend Twist GEARING - Accurate Helical Coils===
+===[[image:Check.jpg|25px]] NEW - Push Bend Twist GEARING - Accurate [[Helical Coil]]s===
 CNC Bender now uses electronic gearing in the rotational twist motion to the feed motion in order to create more accurate helical shapes.  As the Feed axis moves forward, the Rotation axis rotates at a pre-programmed gear ratio in the [[Push Bending Profile]] page.

@@ Line 14: / Line 14: @@
 <br><br>
-===[[image:Check.jpg|25px]] NEW - Push Bend Twist GEARING===
+===[[image:Check.jpg|25px]] NEW - Push Bend Twist GEARING - Accurate Helical Coils===
 CNC Bender now uses electronic gearing in the rotational twist motion to the feed motion in order to create more accurate helical shapes.  As the Feed axis moves forward, the Rotation axis rotates at a pre-programmed gear ratio in the [[Push Bending Profile]] page.

@@ Line 53: / Line 53: @@
 CNC Bender uses an AUTO ADJUST menu in option menus to automatically adjust and set values in the FRB (Feed Rotate Bend) page.
 <br><br>
-A new Push Bend tab is added in the Auto Adjust tab menu in the Bend options that allows you to automatically calculate the angle for a multiple circle helical coil.
+A new Push Bend tab is added in the Auto Adjust tab menu in the Bend options that allows you to automatically calculate the angle for a multiple circle [[helical coil]].
 <br><br>
 Enter the circles in the helix, and press Calc Angle to find an approximate bend angle for a helical coil several levels high.

← Older revision		Revision as of 03:09, 2 January 2009
Line 17:		Line 17:

	CNC Bender now uses electronic gearing in the rotational twist motion to the feed motion in order to create more accurate helical shapes. As the Feed axis moves forward, the Rotation axis rotates at a pre-programmed gear ratio in the [[Push Bending Profile]] page.		CNC Bender now uses electronic gearing in the rotational twist motion to the feed motion in order to create more accurate helical shapes. As the Feed axis moves forward, the Rotation axis rotates at a pre-programmed gear ratio in the [[Push Bending Profile]] page.
		+	<br><br>
		+	Since the twisting action is now electronically geared to the Feed axis, speed changes in the Feed axis will not change the pitch of the helix. Feed speed 1 or 10 makes no difference. Also, it precisely decelerates its rate of twist as the Feed axis enters its deceleration in order to prepare for a hitch feed motion. The effect is precise and repeatable coil production since the twist is completely and precisely dependent on the Feed axis in Push Bending.

	<table>		<table>

@@ Line 21: / Line 21: @@
 <tr>
 <td width=200>
-The older Twist Velocity column is replaced with the '''Twist Gear''' column.  The lowest effective gear ratio value is 0.002 degrees per Feed axis millimeter.
+The older Twist Velocity column is replaced with the '''Twist Gear''' column.
 <br><br>
 This results in a much more accurate synchronization between the Feed and Rotation axes during helical [[push bending]].
 </td>
 <td>

@@ Line 45: / Line 45: @@
 <table>
 <tr>
-<td width="200">
+<td width="300">
 CNC Bender uses an AUTO ADJUST menu in option menus to automatically adjust and set values in the FRB (Feed Rotate Bend) page.

@@ Line 74: / Line 74: @@
 - The resulting angle is the angle necessary to create a helix with the programmed number of circles.
 <br><br>
-- If necessary, further adjust the angle manually by touching the edit box for the bend angle.
+- If necessary, further adjust the angle manually by pressing the edit box for the bend angle.
 <br><br>
 - Press the "This Bend Alone" to replace the current bend angle with the new calculated angle.