CNC Bender v10-20080329 - Revision history

Mcone: /* 25px Change - CNC Processor Safes The Internal Config to a Backup File */

2008-03-29T15:12:52Z

‎25px Change - CNC Processor Safes The Internal Config to a Backup File

Mcone at 15:12, 29 March 2008

2008-03-29T15:12:27Z

Mcone: /* CHANGES to CNC PROCESSOR */

2008-03-29T15:11:35Z

‎CHANGES to CNC PROCESSOR

Mcone at 15:11, 29 March 2008

2008-03-29T15:11:23Z

Mcone at 15:07, 29 March 2008

2008-03-29T15:07:45Z

Mcone at 15:07, 29 March 2008

2008-03-29T15:07:10Z

New page

[[image:cncbender_logo.jpg|400px]]
[[image:Operatorstation_model.jpg|right]]

__NOTOC__

<br>

=CHANGES to CNC PROCESSOR=

===[[image:Check.jpg|25px]] Repair - Command Timeouts are Bypassed During Safe Mode Cycle Hold ===

This version of CNC Processor will now reset the timeout timer for all commands when in Safe Mode Cycle Hold. This means that CNC Processor will no longer timeout immediately after any type of Cycle Hold.

@@ Line 13: / Line 13: @@
-===[[image:Check.jpg|25px]] Change - CNC Processor Safes The Internal Config to a Backup File  ===
+===[[image:Check.jpg|25px]] Change - CNC Processor Saves The Internal Config to a Backup File  ===
 In the previous version, CNC Processor would save it's config file to the CNCProcessor.cfg file.  This would overwrite any changes made by operators in the Low Level menus of CNC Bender.
 <br><br>
 So now CNC Processor saves its state to CNCProcessorBackup.cfg.  This will allow for a comparison between the CNCProcessor.cfg file and the actual contents of CNC Processor memory when it was shutdown.
 ===Other Pages===
 *Back to [[CNC Bender]]
 *Back to [[CNC Bender Software Updates]]

← Older revision		Revision as of 15:12, 29 March 2008
Line 18:		Line 18:
	<br><br>		<br><br>
	So now CNC Processor saves its state to CNCProcessorBackup.cfg. This will allow for a comparison between the CNCProcessor.cfg file and the actual contents of CNC Processor memory when it was shutdown.		So now CNC Processor saves its state to CNCProcessorBackup.cfg. This will allow for a comparison between the CNCProcessor.cfg file and the actual contents of CNC Processor memory when it was shutdown.
		+
		+
		+	===Other Pages===
		+	*Back to [[CNC Bender]]
		+	*Back to [[CNC Bender Software Updates]]

← Older revision		Revision as of 15:11, 29 March 2008
Line 12:		Line 12:
	This version of CNC Processor will now reset the timeout timer for all commands when in [[Safe Mode Cycle Hold]]. This means that CNC Processor will no longer timeout immediately after both types of [[Cycle Hold]].		This version of CNC Processor will now reset the timeout timer for all commands when in [[Safe Mode Cycle Hold]]. This means that CNC Processor will no longer timeout immediately after both types of [[Cycle Hold]].

−
−	~~=CHANGES to CNC PROCESSOR=~~

	===[[image:Check.jpg\|25px]] Change - CNC Processor Safes The Internal Config to a Backup File ===		===[[image:Check.jpg\|25px]] Change - CNC Processor Safes The Internal Config to a Backup File ===

← Older revision		Revision as of 15:11, 29 March 2008
Line 11:		Line 11:

	This version of CNC Processor will now reset the timeout timer for all commands when in [[Safe Mode Cycle Hold]]. This means that CNC Processor will no longer timeout immediately after both types of [[Cycle Hold]].		This version of CNC Processor will now reset the timeout timer for all commands when in [[Safe Mode Cycle Hold]]. This means that CNC Processor will no longer timeout immediately after both types of [[Cycle Hold]].
		+
		+
		+	=CHANGES to CNC PROCESSOR=
		+
		+	===[[image:Check.jpg\|25px]] Change - CNC Processor Safes The Internal Config to a Backup File ===
		+
		+	In the previous version, CNC Processor would save it's config file to the CNCProcessor.cfg file. This would overwrite any changes made by operators in the Low Level menus of CNC Bender.
		+	<br><br>
		+	So now CNC Processor saves its state to CNCProcessorBackup.cfg. This will allow for a comparison between the CNCProcessor.cfg file and the actual contents of CNC Processor memory when it was shutdown.

← Older revision		Revision as of 15:07, 29 March 2008
Line 10:		Line 10:
	===[[image:Check.jpg\|25px]] Repair - Command Timeouts are Bypassed During Safe Mode Cycle Hold ===		===[[image:Check.jpg\|25px]] Repair - Command Timeouts are Bypassed During Safe Mode Cycle Hold ===

−	This version of CNC Processor will now reset the timeout timer for all commands when in Safe Mode Cycle Hold. This means that CNC Processor will no longer timeout immediately after ~~any type~~ of Cycle Hold.	+	This version of CNC Processor will now reset the timeout timer for all commands when in [[Safe Mode Cycle Hold]]. This means that CNC Processor will no longer timeout immediately after both types of [[Cycle Hold]].