CNC Bender v10-20071030 - Revision history

Mcone: /* 25px Optimized for Win2000 or WinXP */

2007-11-03T19:03:13Z

‎25px Optimized for Win2000 or WinXP

Mcone: /* How to UPGRADE */

2007-11-02T13:09:57Z

‎How to UPGRADE

Mcone: /* How to UPGRADE */

2007-11-02T13:09:32Z

‎How to UPGRADE

Mcone: /* 25px New General Dynamic Option - PD Set Pressure */

2007-11-01T14:46:34Z

‎25px New General Dynamic Option - PD Set Pressure

Mcone: /* 25px Production Cycle Time Value */

2007-11-01T14:45:56Z

‎25px Production Cycle Time Value

Mcone: /* 25px Conditional Carriage Cross Slide RETRACT - Only if Clamp is Home */

2007-11-01T14:41:09Z

‎25px Conditional Carriage Cross Slide RETRACT - Only if Clamp is Home

Mcone: /* CHANGES to CNC BENDER */

2007-11-01T14:40:49Z

‎CHANGES to CNC BENDER

Mcone at 14:40, 1 November 2007

2007-11-01T14:40:34Z

Mcone: /* 25px Changed Terminology */

2007-11-01T14:40:13Z

‎25px Changed Terminology

Mcone: /* CHANGES to CNC PROCESSOR */

2007-11-01T14:39:56Z

‎CHANGES to CNC PROCESSOR

← Older revision		Revision as of 19:03, 3 November 2007
Line 100:		Line 100:


−	~~<br><br>~~
−	~~<br><br>~~
	<br><br>		<br><br>
	<br><br>		<br><br>

@@ Line 109: / Line 109: @@
 [[image:Cncbender.jpg|100px|thumb|CNC Bender User Interface for ProControl]]
 If your operator station contains one of the versions listed below, then they can be upgraded through simple self-installation:
-*[[CNC Bender v10-20071030]]
+*[[CNC Bender v10-20071003]]
 *[[CNC Bender v10-20070928]]
 *[[CNC Bender v10-20070920]]

@@ Line 109: / Line 109: @@
 [[image:Cncbender.jpg|100px|thumb|CNC Bender User Interface for ProControl]]
 If your operator station contains one of the versions listed below, then they can be upgraded through simple self-installation:
 *[[CNC Bender v10-20070928]]
 *[[CNC Bender v10-20070920]]
@@ Line 121: / Line 122: @@
-[[image:Nav_down_green.png]][http://www.advancedtubular.com/cncbender/setup_cncbender_v10-20071003.exe| Download the setup file by clicking on this link.]<br>
+[[image:Nav_down_green.png]][http://www.advancedtubular.com/cncbender/setup_cncbender_v10-20071030.exe| Download the setup file by clicking on this link.]<br>
 ''This setup file requires a password to run.
 Please contact [[John Esralian]] for upgrade prices and  password information.''

@@ Line 60: / Line 60: @@
 If this option is enabled, then the PD Set Pressure Output Points are enabled using the new SetPDPressureOutputPoints command.
+[[image:PD_set_Pressure_Output_Points_enable.jpg]]
 <br><br>

← Older revision		Revision as of 14:45, 1 November 2007
Line 52:		Line 52:

	The "Complete Cycle Time" is changed to "Production Cycle Time" and now provides the overall time from part to part.		The "Complete Cycle Time" is changed to "Production Cycle Time" and now provides the overall time from part to part.
		+
		+	<br><br>
		+
		+
		+	===[[image:Check.jpg\|25px]] New General Dynamic Option - PD Set Pressure ===
		+
		+	If this option is enabled, then the PD Set Pressure Output Points are enabled using the new SetPDPressureOutputPoints command.
		+
		+

	<br><br>		<br><br>

@@ Line 9: / Line 9: @@
 <br><br>
-===[[image:Check.jpg|25px]] Conditional Carriage Cross Slide RETRACT - Only if Clamp is Home ===
+===[[image:Check.jpg|25px]] Conditional Carriage Cross Slide RETRACT - Only if DIES ARE RETRACTED ===
 If the clamp is closed, then carriage sliding AWAY from the dies is overridden.

← Older revision		Revision as of 14:40, 1 November 2007
Line 6:		Line 6:

	=CHANGES to CNC BENDER=		=CHANGES to CNC BENDER=
		+
		+	<br><br>

	===[[image:Check.jpg\|25px]] Conditional Carriage Cross Slide RETRACT - Only if Clamp is Home ===		===[[image:Check.jpg\|25px]] Conditional Carriage Cross Slide RETRACT - Only if Clamp is Home ===

← Older revision		Revision as of 14:40, 1 November 2007
Line 1:		Line 1:
	[[image:cncbender_logo.jpg\|400px]]		[[image:cncbender_logo.jpg\|400px]]
		+
		+	__TOC__
		+
		+	<br><br>

	=CHANGES to CNC BENDER=		=CHANGES to CNC BENDER=

← Older revision		Revision as of 14:40, 1 November 2007
Line 74:		Line 74:

	</table>		</table>
		+
		+
		+	<br><br><br>

	=CHANGES to CNC PROCESSOR=		=CHANGES to CNC PROCESSOR=

@@ Line 77: / Line 77: @@
 =CHANGES to CNC PROCESSOR=
-CNC Processor is the program that directly controls the bender actuators.
+===[[image:Check.jpg|25px]] Optimized for Win2000 or WinXP===
-===[[image:Check.jpg|25px]] Disallow Jog Queuing When in Cycle Hold Mode===
+This CNC Processor recognizes the current operating system and optimizes the loop for each operating system.
-−
-CNC Bender no longer allows an operator to jog any axis or actuator if the [[Cycle Hold]] button is pressed.  This mode is slightly different than [[Safe Mode Cycle Hold]], where the safety scanner area is entered.  When the safety scanner or mat is activated, the machine changes to a near [[Zero Energy State]] state.
-−
-[[Cycle Hold]] without stepping on the mat or safety scanner acts as a pause button without changing the bender into safe mode.
-−
-−
-<table cellpadding="35">
-<tr><td width=50></td>
-<td width=300 bgcolor="#f0f0f0">
-<font size=5>[[image:Gear_warning.jpg]] <b>SAFETY NOTE</b><br><br></font>
-<font size=3>'''Do not''' work in a bending machine when it is in regular [[Cycle Hold]] mode!<br><br>
-In regular Cycle Hold, the bender pauses, but all axes stay energized.<br><br>
-If the machine is power on and not in [[Safe Mode Cycle Hold]], then it is critical to keep hands out of the working area of the machine.  Always press the E-stop before working on the machine.
-</font></td></tr></table>
-−
-−
-<br><br>
-−
-===[[image:Check.jpg|25px]] Reduced CPU Usage When Idle===
-[[image:Cncbender_cpuusage.jpg|left]]
-CNC Processor required expanded CPU usage when the bender was powered down or in manual mode.  This had an effect of slowing the CNC Bender user interface.
-−
-Starting with this version, CNC Processor automatically reduces the load on the CPU when in either of these modes.