CNC Bender v10-20070928 - Revision history

Mcone: /* 25px Automatic Cross Check for Module Configuration Files */

2007-10-03T22:44:02Z

‎25px Automatic Cross Check for Module Configuration Files

2007-10-02T14:26:23Z

‎25px Automatic FEED Torque Limit When Outside of Range

2007-10-02T14:25:39Z

‎25pxHandling Axis Motion in the NEGATIVE Region

2007-10-02T14:25:29Z

‎image:Check.jpgWindows System-Up Timer Handler Upgrade

2007-10-02T14:25:13Z

‎image:Check.jpgFile System Setup Change

2007-10-02T14:25:01Z

‎image:Check.jpgUpdate to File DELETE Window

2007-10-02T14:24:51Z

‎image:Check.jpgUpdate to File SAVE Window

2007-10-02T14:24:39Z

‎image:Check.jpgUpdate to File Load User Window

2007-10-02T14:24:28Z

‎CHANGES to CNC BENDER

2007-10-02T14:24:17Z

‎image:Check.jpgAutomatic Cross Check for Module Configuration Files

← Older revision		Revision as of 22:44, 3 October 2007
Line 14:		Line 14:
	<br><br>		<br><br>

−	~~===[[image:Check.jpg\|25px]] Automatic Cross Check for Module Configuration Files===~~

−	~~CNC Bender can get confused if the module configuration files were setup improperly. CNC Bender now performs a module configuration cross check diagnostic every time it starts.~~
−
−	~~<br><br>~~

	===[[image:Check.jpg\|25px]] Update to File Load User Window===		===[[image:Check.jpg\|25px]] Update to File Load User Window===

@@ Line 8: / Line 8: @@
 ===[[image:Check.jpg|25px]] Automatic FEED Torque Limit When Outside of Range===
-Now CNC Bender software uses the FEED torque limiting values programmed into the Low Level menu to ensure that any torque levels outside the range are automatically changed to be within valid range.  This change occurs inside the Process List Builder.
+Now CNC Bender software uses the FEED torque limiting values programmed into the Low Level menu to ensure that any FEED-BEND torque levels outside the range are automatically changed to be within valid range.  This change occurs inside the Process List Builder.
 This will protect the carriage against very low or high torque values in the CNC Bender Process List.

@@ Line 84: / Line 84: @@
 <br>
-===[[image:Check.jpg|25px]]Handling Axis Motion in the NEGATIVE Region===
+===[[image:Check.jpg|25px]] Handling Axis Motion in the NEGATIVE Region===
 It is possible for axes to settle slightly in the negative region when returning to the home position.  In this condition, when sending another ABSOLUTE command for that axis to move to home again, the axis would drive in the wrong direction.  For example, the bend arm would attempt to move to the absolute position of zero degrees by rotating through the bender.

@@ Line 76: / Line 76: @@
 CNC Processor is the program that directly controls the bender actuators.
-===[[image:Check.jpg]]Windows System-Up Timer Handler Upgrade===
+===[[image:Check.jpg|25px]] Windows System-Up Timer Handler Upgrade===
 The timers in CNC Processor references the Windows system-up timer, which is a continuous millisecond counter.  Previous versions of CNC Processor would generate an error after Windows had been running continuously for 24 days 20 minutes.  This problem is not related to how long CNC Bender had been running, but rather, how long Windows had been running since the last reboot.

← Older revision		Revision as of 14:25, 2 October 2007
Line 53:		Line 53:
	<br><br>		<br><br>

−	===[[image:Check.jpg]]File System Setup Change===	+	===[[image:Check.jpg\|25px]] File System Setup Change===

@@ Line 44: / Line 44: @@
 <br><br>
-===[[image:Check.jpg]]Update to File DELETE Window===
+===[[image:Check.jpg|25px]] Update to File DELETE Window===
 CNC Bender's DELETE SAVE menu is simplified.  This is no more multiple path selection with Alias names.

@@ Line 35: / Line 35: @@
 <br><br>
-===[[image:Check.jpg]]Update to File SAVE Window===
+===[[image:Check.jpg|25px]] Update to File SAVE Window===
 CNC Bender's FILE SAVE menu is simplified.  This is no more multiple path selection with Alias names.

@@ Line 20: / Line 20: @@
 <br><br>
-===[[image:Check.jpg]]Update to File Load User Window===
+===[[image:Check.jpg|25px]] Update to File Load User Window===
 '''CNC Bender's FILE LOAD menu is reworked significantly''' based on customer input.

@@ Line 6: / Line 6: @@
 =CHANGES to CNC BENDER=
-===[[image:Check.jpg|25px]]Automatic FEED Torque Limit When Outside of Range===
+===[[image:Check.jpg|25px]] Automatic FEED Torque Limit When Outside of Range===
 Now CNC Bender software uses the FEED torque limiting values programmed into the Low Level menu to ensure that any torque levels outside the range are automatically changed to be within valid range.  This change occurs inside the Process List Builder.

@@ Line 14: / Line 14: @@
 <br><br>
-===[[image:Check.jpg]]Automatic Cross Check for Module Configuration Files===
+===[[image:Check.jpg|25px]] Automatic Cross Check for Module Configuration Files===
 CNC Bender can get confused if the module configuration files were setup improperly.  CNC Bender now performs a module configuration cross check diagnostic every time it starts.